生产方法
- 与 生产方法 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Considering the three principles of the plant indicator for mineral exploration,namely certainty,sensitivity and feasibility,this paper evaluates comprehensively the indicating functions of the eight plants,on the basis of some quantitative indexes such as the relation coefficient between plant ash and ore-forming element,concentration coefficient,etc.
植物找矿法包括地质植物法和植物灰分法,前者为该方法一个古老的形态学分支,国内外均应用较早[1] [2 ] [3] ;后者为该方法的地球化学分支,由于生产实践的需要和科学技术的发展,已从实践上理论上得到肯定,并日益受到重视,特别是在盲矿体的找寻工作中发挥了重要作用。
-
This system can detect the defects of blood lancets real time. In this paper, we, first of all, introduce the blood lancet product system and its detecting method being used, and propose the blueprint of the on-line detection system based on image processing technology.
本文首先介绍了采血针生产系统的特点和检测方法,提出采血针实时图像检测系统的设计思路,并对目标检测方法、图像增强、图像平滑和图像分割等相关的图像处理算法进行了讨论。
-
The effect of the friction moment of bearings on performance is researched. The forming mechanic and influence factors of the friction moment of ball bearing are analyzed. Suitable clearness and groove radius of ball bearings are obtained by experiment and calculation. The relationship between starting moment of ball bearing and various lubricants is analyzed. The measure for reducing the starting moment of ball bearing is put forward, it is the theory basis and reference for ball bearing design of small power unit system.The system is an unstable system when the 24-station ball pen tip production machine is running because of various interferences. It is too hard to describe the system by linear method, so the nonlinear formulation must be used.
研究了小动力头系统轴承摩擦力矩对运转性能的影响,分析了球轴承摩擦力矩的产生机理及影响因素,采用实验和计算的方法得到了动力头球轴承的合理间隙及球轴承沟曲率半径,分析了各种润滑剂与球轴承启动力矩的关系,并提出了减小轴承启动力矩的措施,为小动力头系统的轴承设计提供了理论依据及实践参考。24工位笔头加工机械在笔头的生产加工过程中,由于受到各种因素的干扰是一个不稳定系统,其稳定性会发生一定变化,而且很难用线性方法表述。
-
Finally, the optimal structure designing methods are introduced and the topological optimization method is adopted to optimize the structure of clutch plate hub and clamping disk. The result is that mass of the two parts are less to cut down the cost of production and that provide the reference for the later design.
更多原因最后,介绍了结构优化设计的方法,并采用拓扑优化方法在原有模型的基础上对离合器的从动盘毂和加持盘进行了结构优化,减轻了质量,降低了生产成本,为从动盘毂和夹持盘的设计提供了理论上的参考。
-
Through this method, a flower ball, in the 4 months can produce more than 10000 plantlets, this was a highly effective method.
通过上述方法,1个花球,在4个月可生产上万株组培苗,是一种高效快速的方法。
-
With its characteristic of non-contact、large scale and high precision, it can not be substituted by other contact methods for some special objects and applied fields.
由于视觉测量方法的非接触、大量程和高精度的特点,对一些特殊测量对象和某些生产现场是其它接触式测量方法无法替代的。
-
Production engineering domain urgently need new diagnostic method and experimental technique, and investigate and solve the new diagnostic method of down-hole working conditions on polymer displacement rod pumping system in order to increase crude oil output and ensure the secure and normal production of rod pumping system.
采油工程界迫切需要新的诊断方法和实验技术,研究和解决聚合物驱有杆抽油系统的井下工况新的诊断方法,以提高原油的产量,保证有杆抽油系统的安全、正常生产。
-
The practical measuring of incomplete inner thread ,using the screw gauge and the special fixture is introduced in this article.
结合生产实例介绍了一种利用定制螺纹通止规和夹具测量不完整内螺纹的方法,并讨论了相关结构的加工精度对测量结果的影响,此方法解决了常规测量法无法用于不完整内螺纹检测的问题。
-
This research job analysised the extending roll pass system the finish roll pass system and the ultimate roll groove. The mathematical models and experience formulations used for roll pass design are corrected according to the basic theory and the practical experience of the engineerings. The thread steel bar CARD was set up with the visual program tool-VisualBasic6.0, based on the method of the structural program design.
本课题通过对螺纹钢延伸孔型系统、精轧孔型系统及成品孔型的构成和设计方法的分析,结合螺纹钢孔型系统的基本设计理论和工程技术人员的实际生产经验,对以往孔型设计过程中所使用的数学模型、经验公式等进行了修正,以结构化程序设计方法为基础,采用可视化编程工具VisualBasic6.0建立了螺纹钢计算机辅助孔型设计系统。
-
Some industrial reduction technologies, such as zinc powder method, hydrazine hydrate method, sodium sulfide-zinc powder method etc, were analyzed and compared.
对生产工艺中各种还原方法(锌粉法、水合肼法、硫化钠-锌粉法等)进行了分析对比,指出硫化钠-锌粉法是一种适于工业化的还原方法。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。