球形的

The experimental results show that:(1) for ideal spheres, the attenuation coefficient of velocity is constant, the air drag coefficient is slightly affected by the initial velocity and is a linear function of initial velocity, and (2) for real fragments formed by a warhead, the flight performances are different from ideal spheres, the air drag coefficient is affected by the flight velocity and is a linear function of flight velocity.

实验结果表明：(1)对于理想球形钨合金破片，在同一初始速度条件下，衰减系数为常数，空气阻力系数与初始速度有关，两者成线性关系；(2)对于经历爆轰驱动的球形钨合金破片，由于有轻微的质量损失和变形，速度衰减规律与理想球形钨合金破片有明显的区别，空气阻力系数与飞行速度有关，两者成线性关系。

New contributions of this work are as follows:(1). Preparation of Spherical MgCl_2-Supported Late-Transition Metal Catalysts for Ethylene PolymerizationFacile and effective immobilization of late-transition metal catalysts. 2,3-bis-(2,6-diisopropylphenyl) butane diimine nickel dibromide (1) and 2,6-bis-[1-(2,4,6-trimethylphenylimino)ethyl]pyridine iron dichloride (2), for ethylene polymerization has been achieved, using spherical MgCl_2 supports obtained by thermal dealcoholization of MgCl_2·2.56C_2H_5OH, and the effects of dealcoholization temperature on supported late-transition metal catalysts and the properties of resultant polymers were studied, the results indicated that:1.Supports with appropriate mechanical strength, high surface area and high porosity could be prepared by thermal dealcoholization of spherical MgCl_2·2.56C_2H_5OH supports; 2.BET, XRD, IR, SEM, GPC and DSC analyses indicate that the activities of the supported late-transition metal catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature.

本工作的新贡献如下：(1)、球形氯化镁负载后过渡金属催化荆催化乙烯聚合本文将配合物2，3-双(2，6-二异丙基苯亚胺)丁烷二溴化镍(1)和配合物2，6-二[1-(2，4，6-三甲基苯亚胺)乙基]吡啶二氯化铁(2)分别直接负载于经不同热脱醇温度处理的球形氯化镁载体上，研究了氯化镁载体的脱醇温度对负载化后过渡金属催化剂及其聚合物的影响，研究表明：1、通过对球形MgCl_2·2.56C_2H_5OH载体进行热脱醇处理，可以获得合适机械强度、较高比表面积和较高孔隙度的球形氯化镁载体；2、BET，XRD，IR，SEM，GPC和DSC研究表明，脱醇温度极大地影响负载后过渡金属催化剂的活性和聚合物的性能。

New contributions of this work are as follows:(1). Preparation of Spherical MgCl_2-Supported Late-Transition Metal Catalysts for Ethylene Polymerization Facile and effective immobilization of late-transition metal catalysts. 2,3-bis-(2,6-diisopropylphenyl) butane diimine nickel dibromide (1) and 2,6-bis-[1-(2,4,6-trimethylphenylimino)ethyl]pyridine iron dichloride (2), for ethylene polymerization has been achieved, using spherical MgCl_2 supports obtained by thermal dealcoholization of MgCl_2·2.56C_2H_5OH, and the effects of dealcoholization temperature on supported late-transition metal catalysts and the properties of resultant polymers were studied, the results indicated that: 1.Supports with appropriate mechanical strength, high surface area and high porosity could be prepared by thermal dealcoholization of spherical MgCl_2·2.56C_2H_5OH supports; 2.BET, XRD, IR, SEM, GPC and DSC analyses indicate that the activities of the supported late-transition metal catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature.

本工作的新贡献如下：(1)、球形氯化镁负载后过渡金属催化荆催化乙烯聚合本文将配合物2，3-双(2，6-二异丙基苯亚胺)丁烷二溴化镍(1)和配合物2，6-二[1-(2，4，6-三甲基苯亚胺)乙基]吡啶二氯化铁(2)分别直接负载于经不同热脱醇温度处理的球形氯化镁载体上，研究了氯化镁载体的脱醇温度对负载化后过渡金属催化剂及其聚合物的影响，研究表明： 1、通过对球形MgCl_2·2.56C_2H_5OH载体进行热脱醇处理，可以获得合适机械强度、较高比表面积和较高孔隙度的球形氯化镁载体； 2、BET，XRD，IR，SEM，GPC和DSC研究表明，脱醇温度极大地影响负载后过渡金属催化剂的活性和聚合物的性能。

The plasma frequency of doped semiconductor can be adjusted by changing the dope concentration.

其次，讨论了颜料粒子的单散射性质，计算了球形均匀粒子、包覆球形粒子、旋转椭球粒子以及其它非球形粒子的散射和吸收性质。

The content of the irregular bigger drop phase approached to pyrope. It showed that the crystallization and phase separation mechanics of the glass was the nucleation-and-growth transformation and the crystallization is bulk crystallization. The activation energies of phase separation and crystallization were calculated by the modified Kissinger method, about 310.445 KJ/mol and 249.26 KJ/mol respectively. Using the aluminum hydroxide as the reference, we calibrated the phase separation exothermal enthalpy of the quenched and nucleation treated glass, ca

钠镁侣硅系统徽晶玻瑞快速徽晶化机理的研究利用上式求得混合系统中两相的单位体积相变自由能、两相间的表面能和相互作用参数，分别为刁。6753xlo3了zcm3·、3ss.gozzem3、5.316xlo一JzcmZ和一442 xlol，进而求得球形核的临界半径为nnm，以及一个临界核的成核自由能变化为2石89 x10一14/cm3；成核半径16.5纳米时，球形核稳定存在，实测 1752个球形核中最小核半径为20纳米，与计算结果基本吻合。

In addition, there are bond areas between the new and the primary coverage because of the growing up of the plating coat, which may lead to the emergence of micro crack on the coating owing to such causes as too big or uneven impact during plating process, little distortion of global granular zinc dust inside the plating coat, less tight coalescence of the zinc dust flecks.

由于形成镀层的过程处在酸性环境，在镀层增厚过程中不可避免把酸性溶液包裹在镀层里面，酸性溶液会与金属基体和镀层反应，产生氢气，必然会寻找通道选出，形成微气孔；镀层是逐渐形成的，新生镀层与原有镀层之间存在结合面；镀覆过程由于撞击力过大或者不均匀，镀层内部球形颗粒状锌粉变形较小，球形颗粒与球形颗粒的结合不严密等，这些原因会导致镀层产生微裂纹。

Pome drupe-like, purplish black or bluish, subglobose, succulent, with early caducous sepals leaving an annular ring; seeds 1 or 2, subglobose, large, seed coat thin, cotyledons thickened, plano-convex or semiglobose.

象Pome核果一样，略带紫色黑色或者带蓝色，近球形，多汁，带有早落萼片留下一个环形的圈；种子1或2，近球形，大，瘦的种皮，子叶加厚，平凸的或半球形。

The large-grained spherical copper powder is well compatible and binds securely with the small-grained spherical copper powder. Moreover, the large-grained copper powder has greater gaps between the grains.

小颗粒球形铜粉与钢基体接触面积大，烧结过程中结合牢固、充分，大颗粒球形铜粉与小颗粒球形铜粉烧结相容性好，结合牢靠，并且大颗粒铜粉之间的间隙大，改性聚甲醛可以深埋在大颗粒铜粉的间隙中，使改性聚甲醛工作更可靠。

In this study, a commercial CAD/CAM Software is used to plan and generate the multi-axis tool path, and a table rotating/tilting type five-axis machining center is used to perform the experimental machining operation. The material of the die studied is NAK 80 die tool steel, and the geometries are modeled as concave and convex spherical surfaces. Milling parameters considered are spindle speed, feed rate, and different types of cutting tool path. The experimental results show that the surface roughness for concave spherical surface is about 0.247 μm and roundness is about 0.0283 mm and the surface roughness for convex spherical surface is about 0.250 μm and spherical roundness is about 0.0551 mm under the cutting conditions mentioned in this study.

本研究的实验方法与步骤包括利用商用CAD/CAM系统针对实验对象规划三轴/五轴同动加工路径，并经后处理程式转换，在本实验室之平台倾斜/旋转型之五轴加工机上进行实验，实验对象为NAK80模具钢材料之凹与凸球形曲面之加工，此外考虑的切削条件有主轴转速、进给速度、加工路径等，在本研究所设定之最佳切削条件下，凹球形曲面之真圆度约为0.0283 mm，粗糙度为0.247 μm，而在相同切削条件下，凸球形曲面之真圆度为0.0551 mm，粗糙度为0.250 μm。

The small-grained spherical copper powder is large in the contact area with the steel base and binds sufficiently and firmly in the process of sintering.

小颗粒球形铜粉与钢基体接触面积大，烧结过程中结合充分、牢固，大颗粒球形铜粉与小颗粒球形铜粉烧结相容性好，结合牢靠，并且大颗粒铜粉之间的间隙大，螺旋铜钉层可进一步加大这个间隙，改性聚甲醛可以深埋在螺旋铜钉及大颗粒铜粉的间隙中，使改性聚甲醛工作更可靠。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。