玻璃化的

The original crystal configuration of KGM was destroyed, and the molecular structure was disordered. The glass transition temperature T(subscript g of TKGM was only 13.14℃, and there's an obvious melting decalescence peak at 102℃, the difference between decomposed temperature and melting temperature is above 200℃. This means that TKGM has a good thermoplasticization property.

结果表明：合成了KGM和乙酸乙烯酯、丙烯酸甲酯的接枝共聚物；KGM原有的结晶结构被破坏，分子结构呈现无序化；玻璃化转变温度T(下标 g仅为13.14℃，且在102.5℃处有明显的熔融吸热峰，分解和熔融温差达200℃以上，具有较好的热塑加工性能。

To study the surface treatment of the quartz glass, and the coupling of the albumin protein, we used with the fictionalization of the copolymers, and experimental conditions for protein immobilization.

蛋白质固定化之制作程序系将白蛋白固定於涂有光阻剂共聚物之石英玻璃表面，然后检测蛋白质於280 nm波长附近的吸光特性，以评估蛋白质固定化的效果。

However,for free decay method,its range of changing frequency is very narrow and the initial states of samples are not easily repeated because of the effect of crystallization;for forced oscillation method,the measuring results are seriously affected by crystallization,which is caused by slow heating rates.

然而，自由衰减法有限的变频范围，以及由于受晶化的影响，使两次升温测量时样品的初始状态不易重复；用强迫振动法测量时，同步变频条件限制了升温速率，造成金属玻璃的晶化过程严重影响了测量结果。

Only one parameter is introduced to describe the plasticization effect, and it can be easily estimated by thermodynamic theory about the glass transition temperature depression.

对橡胶态适用的自由体积参数在此模型中保持有效，所引入的表达溶剂可塑化效应的唯一参数β可以通过计算玻璃化温度来确定。

The vitrification process is studied on the basis of vitrification tests of copper and iron slages as well as development of glass ...

在对铜、铁冶炼液态渣进行玻化试验、研制玻璃饰面材料的基础上，对其玻化的工艺进行了研究。

Vitrification, chlorosis, scale-shaped differentiation and failure to root of regenerated shoots frequently occur in industrialized production of tetraploid watermelon Citrullus vulgaris L.

西瓜四倍体工厂化生产中存在试管苗玻璃化、黄化死亡、鳞片状分化、不生根等不利问题，在MS中NH4NO3 含量减半的情况下，前两者可得到有效的控制；用连续增殖、连续壮苗的方法，解决了西瓜四倍体鳞片状分化的难题；用茎尖扩繁的最佳培养基为MS(含半量NH4NO3 )+2 。

This β-eucryptite phase begins to dissolve at 1320℃ or above where the tielite (Al2TiO5) is apparently unstable and decomposed to corundum (Al2O3) and rutile (TiO2). Thirdly, in this dissertation, the influence of composition, crystallization temperature, and time on CTE were investigated detailedly.

然后，对制得微晶玻璃材料的热膨胀性能及力学性能与材料组成的关系，成核剂对玻璃析晶性能和膨胀系数的影响，以及晶化温度和时间的关系进行了分析。

The important feature of modern cockpit is big screen and glassing, which prompt higher request to the display system of cockpit.

座舱的大屏幕化、玻璃化是现代飞机座舱发展的重要特征，这对座舱显示系统提出越来越高的要求。

Two series of polyurethane acrylate grafted acrylic resins (Acr-g-TPU-PETA and Acr-gPPU-PETA) self-emulsifying systems are obtained by grafting -NCO group modified polyurethane acrylates with acrylic copolymer prepared from n-butyl acrylate, styrene,βhydroxyethyl methacrylate and acrylic acid The self-emulsifying systems showed Newtonian fluidity with viscosity closed to that of water, the solid contents were around 30% The T〓 of 15～4℃ for dried film before photocuring favored film formation at room temperature DSC and DMA results showed that PU-PETA is compatible with acrylic resin in the grafted resin The TG and dTG curves for Acr-g-PU-PETA samples were substantially different from the corresponding blends, and the brodened dTG peaks for photocured grafted resin suggest that there might be multiple interactions among chain segments The photocued film of the grafted resins self-emulsifying system exhibited good overall properties with polyurethane acrylate grafts ranging from 30% to 50%, and Acr-g-TPU-PETA series showed better properties than Acr-gPPU-PETA series The adhesion of the photocured film was 1～2 grade, impact strength was 50kg-cm and flexibility was 1mm The Shore hardness and the adhesion of the film decreased markedly if PETA was replaced by HEMA as photoactive group due to the lower C=C double bond content in the grafted resin The polyhydroxy amine-linked thioxanthones photoinitiators can be evenly dispersed in self-emulsifying system without color spot appearing in the dried film The films photocured with IV〓～IV〓 generally exhibited higher Shore hardness, gloss and solventresistance than that cured with Irgacure 2959 and did not induce the rusting of the iron substrate Pigmenting with titanium oxide had no effect on the photocuring The polyhydroxy amine-linked thioxanthone IV〓 and IV〓 can be new candidates for the formulation of titanium oxide pigmented photocurable water-borne coatings for their pale-yellow appearance and slight interference with the color of the coatings WB 4759 with high water-solubility coalesced and separated from the dried resin film, and even induced the rusting of iron substrate.

以丙烯酸丁酯，甲基丙烯酸-β-羟乙酯，丙烯酸及苯乙烯合成厂丙烯酸共聚树脂，并与含-NCO端基的聚氨酯丙烯酸酯接枝反应，经水性化后，得到两个系列（Acr-g-TPU-PETA和Acr-g-PPU-PETA）各5个不同配比的丙烯酸树脂接枝聚氨酯丙烯酸酯自乳化体系，粘度与水相近，为牛顿流体，固含量30％左右。光固化前干燥涂膜的玻璃化转变温度在-15℃～4℃之间，有利于室温下成膜。DSC及DMA谱表明两种树脂基本相容。Acr-g-PU-PETA的热失重行为明显不同于共混材料，接枝样dTG峰明显宽化，表明接枝样中链段之间的相互作刚有多重性，丙烯酸树脂与聚氨酯之间有一定的相容性。接枝树脂自乳化体系光固化涂层的综合性能以聚氨酯丙烯酸酯成分为50％～30％者相对较好，且以Acr-g-TPU-PETA系列更理想。光固化膜的附着力为1～2级，冲击强度为50kg·cm，柔软性多为1mm。以HEMA代替PETA作为接枝树脂的活性基团，碳—碳双键密度太低，光固化膜交联点太少，硬度和附着力均较差。多羟基胺连硫杂蒽酮光引发剂能均匀分散于树脂自乳化体系和接枝树脂干膜中，不出现色斑，光固化膜肖氏硬度一般高于以Irgacure 2959为光引发剂的光固化膜，光泽度及耐丁酮溶剂性能均有所提高，不会诱导铁基生锈，钛白着色对光固化结果几乎没有影响。本论文所合成的多羟基胺连硫杂蒽酮光引发剂IV〓与IV〓为浅黄色，对光固化涂层的颜色干扰较小，为配制钛白着色光固化水性涂料提供了新的光引发剂。水溶性太强的WB 4759在干膜中易聚结析出，且对所附着的铁基有诱导锈蚀作用。

The differences in temper ing process between small thin and thick pieces of glass have been pointed out , technical index of heating furnace and wind grating have also been introduced .

说明了小片薄玻璃在钢化生产过程中与厚玻璃钢化的不同，简要介绍了加热炉和风栅等设备的技术指标。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。