环轴承
- 与 环轴承 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
FYH KYH outside Japan with legislation Block Spherical Bearing Block, Square Block Round diamond ring-type slider Block Block stent Block.
日本 FYH KYH 外球面轴承带立座方形座菱形座圆形座滑块座环型座支架座。
-
I place the bearings in their new home, with enough tube fitted into a block with a 1/4 hole drilled into it. I taped and clayed the bottom to prevent leakage and to protect the hull from epoxy overflow.
我把轴承在他们的新家园,有足够的管装成块与1 1 / 4 钻孔到它,我录音和clayed底部,以防止渗漏和保护船体由环氧溢出。
-
With a constant cross-section of the single-port ring, installed in the ring ditch as Collar or the roller bearing cage maintained.
具有恒定截面的单口环,装在环形沟里作为挡圈将滚子或保持架保持在轴承内。
-
After extended operation, if leakage should occur at the top bearing or across the valve disk of either the Model-B or Model-C valve, this is an indication of wear to the elastomeric seat and/or O-ring seals, requiring their replacement. In most cases, valve replacement will be found less expensive than parts replacement.
在进行操作后,如果泄露出现在型号B或型号C阀门的顶部轴承或阀门阀瓣上,则表明弹性材料阀座和/或O形环密封出现磨损,这时就需要进行更换。
-
Production of various major domestic and international pressure feed granulators the roll, eccentric shaft, the drive wheel, Central-and pulley, bushings, flanged, bearings, shaft and various marine accessories, such as forging, and to undertake various forging processing (forging The largest diameter up to 2000 cm, the largest weighs 2,000 kilograms).
主要生产国内外各种饲料制粒机的压辊、偏心轴、传动轮、环模以及滑轮、衬套、法兰、轴承、各种轴和船用锻件等配件,同时承接各种锻件加工(锻件最大直径可达2000cm,最大的重量为2000公斤)。
-
Rotary servo motor + ball screw up to 2 ~ 5μm, and the requirements of CNC-servo motors - even without coupling gap - thrust bearing - Cooling System - high-precision rolling guide - Nut Block - table closed-loop system as a whole transmission part to lighter, higher precision grating.
旋转伺服电机+滚珠丝杠最高达到2~5μm,且要求CNC-伺服电机-无隙连轴器-止推轴承-冷却系统-高精度滚动导轨-螺母座-工作台闭环整个系统的传动部分要轻量化,光栅精度要高。
-
We stock a complete line of Bearing Caps, Water Baffles, Trunnions, Eddy Current Rings, Shafts, Rotors and Rotators for a variety of dynamometers with shipping within 72 hours for most parts.
我们测功机都有全套的轴承盖,挡水板,枢轴,涡流环,轴,回转器和转子生产线,大多数配件装运3小时。
-
Locomotive diesel engine ; Turbo-supercharger ; Bearing ; Oil seal ; Nozzle ring ; Structure and improvement
机车柴油机;废气涡轮增压器;轴承;油封;喷嘴环;结构与改进
-
Using the software of I-DEAS, the dynamic finite element model of entire reducer was established including gear, ring plate, shaft, bearing and gearbox housing and used to analyze the vibration modal, the time-domain and frequency domain dynamic response and one-third octave velocity grade structural borne noise of double ring gear reducer under dynamic excitation.
利用I-DEAS软件,建立了包括齿轮、环板、传动轴、轴承和箱体的整个减速器系统的动力有限元分析模型,计算了减速器的振动模态、动态激励下的时域和频域响应,以及速度级1/3倍频程结构噪声。
-
NSK uses the standard ISO clearance designations such as C2, Normal, C3, C4 and C5 for bearings with an inner ring bore diameter greater than or equal to 10mm.
恩斯克采用ISO标准的名称,如清除C2 ,正常,补体C3 , C4和C5的轴承内环钻孔直径大于或等于10毫米。
- 推荐网络例句
-
She gently rebuff ed him, but agreed that they could be friends
她婉言拒绝了,但同意作为朋友相处。
-
If in the penal farm, you were sure to be criticized.
要是在劳改农场,你等着挨绳子吧!
-
Several theories about reigniting and extinguishing of the arc have been refered.
本文综合考虑了几种电弧重燃和熄灭理论。