环氧树脂

With this model,the temperature growth process and temperature distribution of unit wall of epoxy resin,7740# glass,microcrystal glass and silicon units filled with lead styphnate were obtained by numerical simulation.

根据燃烧传热原理，建立了阵列单元燃烧传热过程的一维有限差分模型，运用此模型对装填斯蒂酚酸铅的7740玻璃、环氧树脂、微晶玻璃和硅药室单元燃烧40~80 ms过程中室壁温度成长和温度分布进行了数值模拟。

In ultrasonic field, authors studied solidify of water base epoxy dope and suspend and decentralization of millicron grain in water base epoxy resin, developed a series of water base dope.

超声场条件下，试验研究水基环氧涂料固化以及纳米颗粒在水基环氧树脂中的悬浮分散，研制出系列水基涂料。

This moire effect is used in combination with photoelasticity to separate the principle stresses in the two-dimensional stress problem. The model was made by epoxy resin, its surface was covered with a printing film, which have 300 lines per inch.

以每时300道条纹的网格薄膜贴在环氧树脂模型上，采用光测法冻结技术把应力冻结下来，然后在偏振场中测取等差线，与标准网板重叠测取水平位移及垂直位移条纹图。

This is demonstrated (in form of examples of the author's own experience) for an unfilled semicrystalline polypropylene, a blend of epoxy resin with an elastomeric toughener, an injection moldable short fiber reinforced polyethyleneterephthalate, a discontinuous aligned fiber/polyethersulfone composite, and a high performance continuous fiber reinforced polymer composite system respectively.

这是表明（在表格的例子，该作者本身的经验）为一空半聚丙烯，共混环氧树脂树脂与橡胶增韧剂，一注射模压的短纤维增强 polyethyleneterephthalate ，间断不结盟纤维/聚醚砜复合材料，和一种高性能的连续纤维增强聚合物复合系统分别。

Manufactures aerospace products including DMS-4-828 moldable shim material, MagRubber magnetic rubber inspection material, replication materials and sealants, special purpose foams, epoxies, and resins.

生产航空航天产品：成形垫片材料、MagRubber磁性橡胶检验材料、复制材料和密封胶、泡沫、环氧树脂和松香。

Cure behavior of F-51 epoxy resin and DAIP was studied by DSC. The influence of the different compositions on the co-cure resins morphosis and the heat resistance were researched.

研究了F-51环氧树脂和DAIP共固化的固化行为、不同配比对共固化物形态结构的影响；并研究了不同配比对固化物耐热性的影响。

Any of various similar adhesives,such as paste,mucilage,or epoxy.

胶粘物一种相似的粘合剂，如浆糊、胶水或环氧树脂

His moveable wings, set in rusty epoxy and multi-coloured crystals in Pointiage?

可活动的翅膀上镶嵌环氧树脂并以Pointiage？

Surface treatment has galvanized, nickel, gold, silver, copper, black, epoxy resin coating and heat treatment.

表面处理有镀锌、镍、金、银、铜、染黑、环氧树脂喷涂及热处理。

The microstructure morphology of the epoxy resin/nitrile rubber system and the influence of rubber kinds.

利用扫描电子显微镜等研究了环氧树脂/丁腈橡胶体系的微观结构形态以及橡胶种类、用量等对增韧效果的影响。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。