特征参数

With the combination of lighting, cooling and heating under daylighting, the study on the effect of the key characteristic parameters on total energy consumption is provided. The validation of the comparability of daylight distribution for building antetype and model is made through theoretical analysis and simulating calculation in the thesis. Due to the variable sky condition, daylighting factor is used for experimental validation instead of illuminance. The error analysis of several testing methods used in the experiment is conducted, followed by the experimental validation of the effect of WWR, sill and transmittance on daylighting factor distribution.

基于天空状态的多变性，提出用天然采光因数替代照度进行实验验证，对实验中的几种测试方法进行了误差分析，并通过实验验证了窗墙比、窗台高和透光率对天然采光因数分布的影响。4 为了更直观地分析各参数对照明节电的影响，提出了"特征点"、"特征线"和"特征距离"等概念；分析了天然采光下的照明节能状况，综合考虑照明、采暖和空调能耗，计算分析了几个主要特性参数对总能耗的影响。

OBJECTIVE To design and develop a clinical pharmacokinetics and individual drug dosage regimens system CPKDP program for estimating individual pharmacokinetic parameters and optimizing individualizing dosage regimens using routine clinical data of plasma levels. METHODS According to the principle of population pharmacokinetics and Bayes" formula, CPKDP program was written with FOXPRO 2.6 and BORLAND C++ 3.1, and was run on 486 microcomputer with UCDOS 5.0. RESULTS CPKDP program was adapted for drugs with different characteristics of pharmacokinetics, and for single dose or multiple dose administration. Using 1 or 2 measured drug concentrations, individual patient"s pharmacokinetic parameters were estimated based on population-average pharm-acokinetic parameters. CONCLUSION CPKDP program is applied for estimating pharmacokinetic parameters and optimizing drug therapy in individual patients.

目的为利用临床常规监测的血药浓度数据估算病人的个体药动学参数，优化给药方案，设计、研制了临床药动学给药个体化系统CPKDP程序方法依据群体药动学原理及Bayes公式，CPKDP程序用FOXPRO 2.6和BORLAND C++ 3.1开发，在希望汉字系统UCDOS 5.0平台上运行结果CPKDP程序适用于具有不同药动学特征的多种药物，适用于不同给药途径的单剂量或多剂量给药在群体药动学参数的基础上，结合病人个体特征，以1，2个血药浓度作为反馈，即可拟合估算个体药动学参数，优化给药方案结论经初步应用，CPKDP程序是应用Bayes反馈法开展临床个体化给药工作非常实用的工具

Firstly, we give the definition of so-called value of edge information which is used to measure the quantity of marginal character in certain block. secondly, we used the information contained in the basic characteristic block to initialize the parameters of model and then detect the corner feature points to accurate the final value of parameters.

该方法先定义边缘特征量，逐点计算各像素点邻域的边缘信息量大小，并采用局部非极大值抑制及阈值法进行排除，最终确定基本特征块；先利用基本特征块的位置信息初步估计模型参数，再提取特征点对模型参数进行修正；最后，对图像进行拼接获得更大视野更高分辨率的拼接图。

The characteristic exponent based on a probabilistic dynamical system is calculated, which provides some useful information on unstable periodic orbits of the chaotic economic dynamical system. An effective controlling parameter is chosen by discussing the sign of the characteristic exponent. Furthermore, the control regions of the parameter variable are proposed. Therefore the controllable domain of chaos in the chaotic economic model can be obtained.

提出一种等价关系，计算基于概率的动力系统的特征指数，给出混沌经济动力系统的不稳定周期轨道的有用信息，通过讨论特征指数的符号，选择有效的控制参数，得到相应的控制参数取值范围，从而得到混沌经济模型中的参数变量的混沌控制域。

As long as the root of the characteristic equation is within the unit circle of z-plane and the corresponding PID parameter is got, the closed loop control system is sure to be stable. Although the root of the characteristic equation can vary within the unit circle of z-plane,different value may affect the control property differently.

本文所采用的这种确定PID参数的方法，虽然可以使特征方程的根在z平面的单位圆内任意取值，但各种取值情况对变风量空调系统的控制品质的影响却不同，因此，要对各种特征方程的根的取值情况进行寻优，本文采用遗传算法对特征方程的根进行寻优，从而使控制器的参数得以优化。

This article detailedly expatiated upon the principles, contents and methods of cropland classification; it analyzed the necessity to combine the work of cropland classification with GIS technology, summarized the attributions of ARC/INFOand some other related softwares; it established the technologic route of cropland classification supported by GIS, by a case study in Liwu Town,Li County Hebei Province, this article expatiated the practicable mechanism of combining the function of ARC/INFO with the work of cropland classification, and put forward some new ideas and approaches of utilizing GIS: this paper put forward the idea of coding the polygons in the basic graphic database such as soil map and land use map according to their attributes, and put forward the detailed coding project; based on the code databases, it expatiated upon the detailed approaches to create single梖actor map and output the final classification map; it put forward the principles and the method of creating classification units in the environment of GIS, that is how to keep the lines of soil polygon, the border of districts and the important objects such as residential areas, banks of rivers and roads ,and how to overlap single梖actor soil map and land use map, and to delete some vector lines of the overlapped map appropriately; it detailed the methods of creating mathematic model of classification coefficients in the environment of computer, and used FOXPRO6.0 programs to realize the automation of calculating coefficients; it represented the method of plotting the final map by overlapping various coverages according to the code tables and lookup tables, the process of outputting the cropland classifying map was finished by program.

本文法对耕地等别划分的原则、内容及方法作了较详细的阐述，介绍了多系数综合修正法的耕地等别计算方法及其具体应用和AHP的确权方法；分析了耕地等别划分工作与地理信息系统技术相结合的必要性，简要介绍了地理信息系统软件ARC／INFO及其他相关软件的功能特点，制定了地理信息系统支持下耕地等别划分的技术路线，通过对河北省蠡县蠡吾镇的实证研究，重点阐述了ARC／INFO及相关数据库软件与耕地等别划分结合的有效机制及GIS应用的一些新思想、新方法：提山了对土壤图和土地利用现状图等基础图形数据库进行特征编码的思想和具体的编码方案，阐述了基于与图形库相链接的特征编码表，单因素图提取、成果图的输出的具体实现方法；提出了GIS环境下耕地单元划分的原则和方法，即在保留土壤因素图斑界线、行政界线和重要地物等的原则下，将土壤单因素图和土地利用现状图进行拓扑叠加，对叠加图中的矢量线进行适当的删除；阐述了在计算机环境下，耕地分等参数计算模型建立的方法，并用FOXPRO6.0语言程序实现了参数计算的自动化；阐述了根据图形库特征编码表和建立绘图符号查找表，按不同图层叠加绘制成果图的方法，该过程用命令程序实现耕地等别图的输出。

In this dissertation, based on the extraction of meaningful polarization information, the polarimetric speckle reduction, polarimetric contrast enhancement, polarimetric classification and ship detection in polarimetric SAR images are systemically studied. During the study, some new concepts and methods are introduced, which are supported by the application to measured Pol-SAR data. The innovations of this dissertation are as follows: 1 A simplified schem is proposed to reduce the complexity of scattering-model-based speckle filtering. 2 Extend the expression of polarimetric correlation coefficient to help distinguishing targets. In addition, introduce the quantized parameters of polarimetric signature so as to show the differentiae in quantity in co-polar power, cross-polar power and shapes of polarization signatures among targets. 3 Define a new parameter of difference degree between targets, which can be used for express the difference between both coherent and distributed scatters.

论文在较系统的研究目标特征量提取方法和特征量所包含的物理意义的基础上，对极化SAR图像降斑、极化对比增强、极化SAR图像分类以及极化SAR图像中海上舰船目标检测等方面进行了研究，并提出了一些新的概念和方法，对实测数据的处理结果表明，这些新的概念和方法对于极化SAR信息处理是有效的，本文的主要创新成果包括以下方面： 1）针对基于预分类的MMSE极化降斑方法实现过程非常复杂的问题，提出了简化方案，并验证了方案的有效性； 2）扩展了极化相关系数的表示方法，这种扩展增强了极化相关系数对目标的区分效果；另外还提出了极化特征图量化参数，可以从量上表征不同目标间相同极化和交叉极化的回波功率差异和极化特征图形状差异； 3）定义了目标间的差异度参数，它不仅可以用于描述相干目标，还可以用于描述分布目标的差别程度。

Parametrical feature library is developed with characterization and parameterization technology, and it can provide user with well defined feature to complete the design of part.

参数化特征库基于特征造型技术和参数化技术创建，用户可以运用这些定义好的库特征元件完善零件的设计，特征库还可以根据需要不断扩充。

Based on analysis and compare of all kinds of precept-sorting of feature of plastic product for the different structural plastic product, a 3D feature library of plastic product was built on the platform by integrating Feature-Modeling technique with parametric technique. The feature schleps its information of non-geometry by database-externed technique of the entity. After building the database of plastic material, the module of choice of plastic material is developed by technology of ODBC. The plastic product can be sculpted by calling of feature of plastic product and inputting parameters interactively.

针对不同结构类型的塑件，在全面分析、比较塑件特征分类的各种方案的基础上，采用三维特征建模技术和参数化技术，建立了注塑产品的三维特征库；应用实体扩展数据库技术，使特征携带非几何信息；再在建立塑料物性数据库的基础上，采用ODBC技术，开发了塑料材料选择模块；通过塑件特征的调用和人机交互输入参数的方法进行塑件三维造型，再把塑件的三维实体和塑件的非几何信息结合起来，生成塑件全信息模型。

Main points of the thesis are as follows:(1) The main function models and information relations between these models in the CAPP system in the integrated CAD/CAM project are explained, a new process plan design method is mentioned based on analyses of process plan design. This method is based on the process plan prototype, and develops the prototype little by little until the perfect process plan is completed, the prospect of this method is discussed;(2) The feature abstracting rules and methods are studied, a feature coding system is developed based on GT, all the defined feature models are described by the mathematical methods;(3) The integrated method of CAD/CAPP based on features is mentioned, this method defines a feature exchanging model, and develops an interface software to exchange design data into technology data base, this technology data base includes the design and technology information of the parts;(4) The process plan reasoning method based on features is created, this method uses Mycin algorithm to solve the reasoning of the feature process plan. A process plan making system is developed. In this system part process plan is made by the semi-intelligent method, this method uses the feature reasoning, feature process chain searching and man-computer talking together;(5) The main structure of the HOPE system is introduced, a shaft drawing and its process plan made by this system are shown, the data process problem in process drawing making is also discussed;(6) A new method of describing process rule is introduced, this method uses IfThen rules and neural nets weight values together to describe process rules, the BP algorithm is adopted in this method;(7) The optimal machining sequence problem of the process steps on the same fixturing is discussed, optimal algorithms SA is applied to solve this problem, the result shows that this method is more efficient than the traditional method;(8) All jobs in the thesis are summarized. In order to carry out the research in the future, some rational proposals are given.

全文论述的内容主要有下列几个方面：(1)较为系统地阐述了CAD／CAM一体化工程项目中CAPP系统的主要功能模块及其信息流程，在分析工艺设计过程的基础上，提出了基于特征原型的渐进式工艺设计方法，并探讨了该方法的应用前景；(2)研究了零件特征提取的原则和方法，在成组技术的基础上，开发了一套基于特征的分类编码系统，并在提取零件特征的基础上，定义了零件特征的数据模型，开发了基于轴类零件特征的参数化设计系统；(3)研究了基于特征的CAD／CAPP集成的方法，通过定义零件特征数据模型的存储结构，开发了将设计数据转换到工艺数据库中的接口程序，为后续的CAPP系统提供必要的零件形状和工艺信息；(4)研究了基于特征的工艺推理方法，将Mycin算法应用到工艺决策中，开发了基于特征的工艺推理及工艺方案生成系统，在系统中综合运用特征推理、特征加工工艺链查询及人机对话相结合的半智能化方法确定零件加工工艺；(5)介绍了整个HOPE系统的总体结构，通过运行HOPE系统绘出了一轴类零件的零件图，并生成了该零件的加工工艺方案，初步探讨了基于特征的工序图生成技术中数据处理问题；(6)研究了工艺设计过程中知识如何有效表示的问题，提出了将显式的IF-THEN规则表示与隐式神经网络权值表示相结合的工艺知识表示方法，并利用BP算法进行了工艺知识表示的初步研究；(7)研究了工艺设计过程中同一安装下工步优化排序问题，利用神经网络中基于模拟退火的理论来解决该工步优化排序问题，实践证明该方法较传统的算法具有更高的效率；(8)总结了本文所进行的研究工作，为今后进一步开展工作提出了较为合理的建议。

According to the clear water experiment, aeration performance of the new equipment is good with high total oxygen transfer coefficient and oxygen utilization ratio.

曝气设备的动力效率在叶轮转速为120rpm～150rpm时取得最大值，此时氧利用率和充氧能力也具有较高值。

The environmental stability of that world - including its crushing pressures and icy darkness - means that some of its most famous inhabitants have survived for eons as evolutionary throwbacks, their bodies undergoing little change.

稳定的海底环境─包括能把人压扁的压力和冰冷的黑暗─意谓海底某些最知名的栖居生物已以演化返祖的样态活了万世，形体几无变化。