片簧

The dissolution of offload valve spool: Using circlip pliers remove the valve core and valve located at the junction of the circlip, and then pipe clamp screwed up spool, remove the inside of the cylinder, valves, O-rings, U-type ring, spring and immersed into the cleaning agent, and then split out the valve on the inlet, the whole body into the soaking, this time, the demolition process by Dutch valve has been completed.

拆减荷阀阀芯：用卡簧钳取下位于阀芯与阀体连接处的卡簧，再用管钳拧出阀芯，取出里面的气缸、阀片、O型圈、U型圈、弹簧并放入清洗剂中浸泡，再拆出阀体上的进气口，将整个阀体放入浸泡，此时，减荷阀的拆卸过程已完成。

Since the machine speed fast, the strength of the avulsing, the drum in particular for the imprint of the drum and carry it and carry it to remain in force General 16kg than radiograph, clishion always maintained in a clean, open and closed freely, in a pipe pressure, wearless, teeth-axis in the spring of elastic to a value greater than the small spring force in its teeth.

由于机不缓迟，不粘贴辛不小，各滚筒不入格是不抬印滚筒叼牙的叼辛凡是给保留在16kg以上，且牙片、牙垫本末给保留肮脏、开闭自若，处于叼辛陡均、无磨损的精良状况，牙轴边的扭簧的弹辛给不小于各叼牙小弹簧辛的总和。

The FEA analysis and the static loading test of a new three-leaf spring are studied in this paper.

利用有限元分析方法和静态应力试验方法，对新的3片簧做了有限元分析计算和试验验证

One of several metal strips forming a leaf spring .

簧片构成片簧的几个金属片中的一个。。

Leaf spring clamping the detent to contact ratchet wheel.

片簧顶住棘爪，使其始终与棘轮保持接触

Parallel leaf spring;half beam model;guiding displacement;coupled displacement

平行片簧；半段梁模型；导向位移；耦合位移

The finite element model contains the establishment of the model with variable section element and the disposal of the boundary conditions of the suction valve with point stop and the discharge valve with back plate.

本文采用变截面梁单元建立了吸气与排气舌簧阀的有限元模型并处理了具有点状升程限制器的吸气阀片和具有背板曲线升程限制器的排气阀片的边界条件。

Finite element analysis method was used to analyze a three-leaf spring under vertical loads, in which the brick element of eight nodes was used to model the spring leaves and the contact analysis was introduced to simulate the process of the leaves gradually coming into contact with each other.

应用有限元法对一种在垂直力作用下的3片式钢板弹簧进行分析，其中应用8节点块单元对板簧进行实体建模，采用接触分析来模拟板簧各片逐渐进入接触的情况。

Under the conditions of keeping other design parameters constant, design thickness of valve flap increases with the mass increment on single wheel spring of the vehicle; throttle gap of oil-air spring is in linear decrement relationship with mass on single wheel spring. For each mass increment of 100kg on tested single wheel spring, design thickness of throttle valve flap will increase by 0.007mm and the throttle gap will decrease by 0.001mm.

在其它设计参数保持不变的情况下，阀片设计厚度随车辆单轮簧上质量的增加而增加；油气弹簧节流缝隙与单轮簧上质量成线性递减关系；试验的单轮簧上质量每增加100kg则节流阀片设计厚度将增加0.007mm，节流缝隙将减小0.001mm。

Produced by compression springs, Extension Spring, torsion spring,¨, battery spring, spring roll cochlea, square flat steel spring, steel spring, electrical switch springs, special-shaped springs, clockwork springs, valve spring, a snake-type spring, craft spring a variety of precision springs range from 0.15 ~ 8mm diameter, widely used in electronics, computer, hardware, electrical, electronics, machinery, tools, toys, locks, and automobile industries, by the vast numbers of clients of all ages.

生产的压缩弹簧、拉簧、扭簧、卡簧、电池簧、蜗卷弹簧、方扁钢弹簧、钢片弹簧、电器开关弹簧、异型弹簧、发条弹簧、气门弹簧、蛇型弹簧、工艺弹簧等各种精密弹簧线径0.15~8mm不等，广泛适用于电子、电脑、五金、电机、电器、机械、工具、玩具、锁具、汽车等行业，深受广大客户的青睐。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失