燃烧性

In some extent, increasing the area of fuel nozzle will be improve the combustion efficiency of DR; 3, the angle between dual air-inlets have complex influence with the combustion of DR.

研究结果表明：(1)补燃室头部距离的增加能增强补燃室头部回流以及提高燃料在补燃室后段分布的均匀性，但也减少了燃料与空气在补燃室后段进行掺混和燃烧的长度：(2)在一定范围内，增加一次燃气喷嘴面积能提高冲压发动机燃料的燃烧效率：(3)进气道夹角对冲压发动机中燃料的燃烧影响复杂，对于采用对称结构喷嘴的冲压发动机，当进气道夹角等于180°时，燃料与空气的掺混效果最好；而对于一次燃气喷嘴采用不同偏心结构的冲压发动机，补燃室内流场与燃料燃烧效率随进气道夹角变化的规律基本相似。

Some conclusions are followed:(1)the reaction ratio of boron is 12% in primary combustion;(2)the degree of agglomeration can be decreased adopting boron coated with AP;(3)the content of oxygen is very important for afterburning efficiency;(4)the afterburning efficiency will be changed with different air-gas ratio;(5)the head distance of after-burning chamber is increasing, the circumfluence in the head of after-burning chamber is stronger and the distribution of fuel backward the after-burning chamber is more well-proportioned.(6)the combustion efficiency of DR will be improved by increasing the area of fuel nozzle.(7)the angle between dual air-inlets have complex influence with the combustion of DR.

通过本项研究，取得如下结论：（1）一次燃烧硼反应比例在12～15％之间；（2）AP包覆硼，可以降低硼结团度，有利于一次燃烧喷射效率的提高，也有利于硼在补燃室进行二次燃烧；（3）进气空气中的氧含量对二次燃烧非常重要；（4）对于一定配方的含硼富燃推进剂，不同的空燃比，二次燃烧效率不同；（5）补燃室头部距离的增加能增强补燃室头部回流以及提高燃料在补燃室后段分布的均匀性；（6）在一定范围内，增加一次燃气喷嘴面积能提高冲压发动机燃料的燃烧效率；（7）进气道夹角对补燃室内燃料的燃烧影响复杂。

Some parameters of coal properties which are not a linear combination of the individual index in weight of blending coal, such as Hardgrove grindability index, screen analysis, ash fusibility, ect.

从煤在不同类型锅炉的燃烧方式出发，讨论了煤质特性对燃烧工况及对环境的影响，以及一些非加和性煤质指标，如可磨性、粒度组成、煤炭熔融性等对动力配煤的影响，进而提出选定动力配煤方案的原则

The main products are: Hammer, thermal conductivity detector, permeameter, contraction of the expansion device, hand-held strain gauge, waterproof material detector, low-bending device, slag ball content in separators, heat load tester, performance test combustion furnace, a variety of thickness, thermal expansion of graphite electrode NG, coal strength meter, electric tamping device, hydrophobicity tester, mineral wool density meter, concrete drilling sampling machines, sawing machines, removed machine, setstube machine, hydraulic bending machine, impervious tester, determination of heat resistance, heating telescopic measuring device, an extension device, penetration tester, small meter, viscometer, drying time tester, pencil hardness tester, pendulum hardness, the adhesion tester, film zoned grid, and resistant to scrubbing detector, solvent resistance detector, wearable device, flat grinding device, wear-resistant coating shakeout device, staining resistance tester, impact tester , piercing instrument, instrument bending film, film coating, and sanding machines, cone-shaped grinding, high-speed dispersion machine, three roller grinder, Scratch tester, indentation tester, gloss Miriam, white tester, fresh video of Miriam, Miriam reflectivity, iron cobalt colorimeter, paint density cup, crack resistance testing apparatus, leveling device, flow hanging device, visual color box, the minimum temperature detector into a grinding, low temperature brittleness tester, visual color boxes, electronic pull machine, Mooney Viscometer, vulcanizing device, the proportion of direct-reading, the cold compression tester, heritage wearable device, Heritage scratch device, the friction coefficient detector, coating Detect zoned grid plate , coating resistance tester, such as burning a variety of test equipment.

主要产品有：回弹仪、导热系数测定仪、渗透仪、收缩膨胀仪、手持应变仪、防水材料检测仪、低温弯折仪、渣球含量分离器、热荷重试验仪、燃烧性能试验炉、各种测厚仪、石墨电极热膨胀仪、煤强度测定仪、电动击实仪、憎水性测试仪、矿棉容重测定仪、混凝土钻孔取样机、锯切机、磨平机、套丝切管机、液压弯管机、不透水试验仪、耐热性测定具、加热伸缩测定器、延伸仪、针入度仪、细度计、粘度计、干燥时间试验器、铅笔硬度计、摆式硬度计、附着力测试仪、漆膜划格器、耐洗刷测定仪、耐溶剂测定仪、耐磨仪、平磨仪、涂层落砂耐磨仪、耐沾污测试仪、冲击试验仪、穿孔仪、漆膜弯曲仪、涂膜涂布器、砂磨机、锥形磨、高速分散机、三滚研磨机、划痕试验仪、压痕试验仪、光泽仪、白度仪、鲜映性仪、反射率仪、铁钴比色计、涂料密度杯、抗裂性试验仪、流平仪、流挂仪、目视比色箱、最低成磨温度测定仪、低温脆性试验仪、目视比色箱、电子拉力机、门尼粘度仪、硫化仪、直读比重计、压缩耐寒试验仪、文物耐磨仪、文物划痕仪、摩擦系数测定仪、涂层检测划格板、涂层耐燃烧试验仪等多种试验仪器。

By designing the mould to change the propellants model frame, selecting differentmaterials as propellant seal layer agents, studying the preparation technics, we havepreferably solved the PSS seal layer pressurize and combustion disciplinarian problem, andobtained the remarkable increasing burning surface effect.The practical increment ofΓvalue reachs 3.2 upwards conducting closed bomb firings, comparing with 19 holepropellants—the best progressivity burning in the present, whose practical increment ofΓvalue is 1.2, the PSS amplitude ofΓvalue exceeds 2.5 times.

通过药型结构和模具的设计、端面密封材料的选择和制备工艺的研究，较好地解决了PSS发射药的端面密封和燃烧规律控制问题，获得了显著的增面性燃烧效果，密闭爆发器实验中燃气生成猛度的实际增量达到了3.2以上，与目前增面性最好的19孔发射药实际增量的1.2左右相比，增幅超过了2.5倍。

Mechanical properties and combusition characteristics were affected evidently by the solid grain configuration and its character. Mechanical propertiesof the material system could be improved by adopting RDX and proper granularpropellants granularity rank-match. It is favorable to obtain progressivity burning effect byaffiliating increasing burning surface propellant grains. Affiliating fast burning componentthese burning rate regulator in the bond system can quicken burning rate of propellants andimprove burning progressivity.

固体颗粒形态及其性质对力学性能和燃烧性能具有较大的影响，采用RDX与适当颗粒度的固体发射药的粒度级配有利于改善力学性能，加入增面燃烧的发射药颗粒，有利于获得渐增性的燃烧效果，在粘合剂体系中加入速燃组份等燃速调节剂，可加快发射药的燃气生成速率，改善燃烧的渐增性。

Using shape function andclassical interior ballistics theory, the influence relation of the PSS model parameter affectto splitting opportunity, increasing burning surface and interior ballistics characteristicswas researched.The splitting opportunity of PSS appears ahead the academic intending, thereason is that the thickness of outside burning layer is asymmetry, the thinner area splitsearlier, and the thicker area splits later, consequently, the PSS put up progressivity burningeffect. From the practical look, the burning progressivity effect is more profitable than thatincreasing burning surface suddenly.

采用形状函数和经典内弹道理论，研究了PSS发射药的药型参数对分裂时机、燃烧增面性和内弹道性能的影响关系，PSS发射药的分裂时机比理论预计值提前出现，原因是外侧面的燃烧层厚度不均匀，薄的地方先分裂，厚的地方晚分裂，从而表现出了渐增性的燃烧效果，从应用的角度出发，渐增性燃烧的效果比突增的效果要好。

Considering a spherical porous carbon particle immersed in a static ambient atmosphere, the combustion characteristics under three basic conditions: frozen flow, equilibrium flow, partial flow are solved in a half-analytical and half-numerical way. By using the LAEA (Large Activation Energy Asymptotic Method), the departure value of some parameters such as combustion rate, temperature, and concentration are obtained. On this basis, the rules of a carbon particle combustion under various conditions when the gas phase Damk〓hler number is in the range of 0,+∞ are summarized.

建立氧化性环境中相对静止的多孔炭粒燃烧的控制方程，采用半解析、半数值方法求解出炭粒在冻结流、部分流、平衡流三种基本情况下的燃烧规律，并采用大活化能渐近匹配方法，计算出偏离冻结流、偏离平衡流情况下燃烧速率、温度及组分浓度等参数的偏离解，进而总结出炭粒在气相Damk〓hler数为0，∞整个范围内燃烧特性变化规律。

By regression of experimental data, therules of the linkage between these factors, which will provide a theoretical basis for designing BBP with different scales.3 Using thermal analysis technology and dynamic thermogravimetry, the paper studies combustion kinetic characteristics of 3 types of agricultural crops at different rate of temperature rise, and thus, achieved dynamic parameters of these fuels at different rate of temperature, established dynamic model of straw combustion, which reflects the dynamic process in the fast combustion area.4 Characteristics of straw briquette combustion was experimented, focusing on the impact of straw type, temperature, air supply, and density, diameter, and weight of briquette on the combustion speed, and the following conclusions were drawn:(1) combustion of straw briquette fuel is static permeation diffusion combustion;(2) temperature has a larger impact on the speed of straw briquette combustion than air supply; the higher the combustion temperature is, the faster volatilizable component separates out, and the less steady the combustion is;(3) density of briquette fuel has impact on the speed of volatilizable component separation and therefore the combustion speed;(4) increase of diameter and weight of briquette fuel increases the average combustion speed in the initial stage, and that in the later stages is comparatively steady;(5) the proportion of volatilizable component in straw briquette fuel is high, therefore, the temperature control during combustion under the rational ventilation condition is essential to ensure its safe combustion.5 Using the above-mentioned results of experiments and theoretical analysis, and based on thought of hydraulic driven and bi-direction compression, the hydraulic system and compression parts of the HBP BBP are re-designed in terms of industrialization.

利用热分析技术，采用动态热重实验法，对我国的三大农作物秸秆在不同升温速率下的燃烧动力学特性进行了较系统的研究。得到了各原料在不同升温速率下的动力学参数；建立了秸秆燃烧的动力学模型，该模型反映了秸秆迅速燃烧区的动力学过程。 4 对秸秆成型燃料的燃烧特性进行了试验研究。着重研究了秸秆河南农业大学博士学位论文巫的种类、温度、空气供给量、成型燃料密度、直径、质量对成型燃料燃烧速度的影响并得出如下主要结论：①秸秆成型燃料的燃烧方式属于静态渗透式扩散燃烧。②秸秆成型燃料燃烧速度受温度的影响大于通风量燃烧速度的影响：燃烧温度越高，挥发分析出速度越快，燃烧平稳性愈差。③成型燃料密度影响成型燃料挥发分的析出速度，影响燃烧速度。④成型燃料直径和质量的增加，使得燃烧初期的平均燃烧速度增大，中后期的平均燃烧速度相对平稳。⑤秸秆成型燃料含挥发分比例高，因此合理配风下的控温燃烧是保证其完全燃烧的关键。 5运用已取得的试验和理论分析结果，以液压驱动、双向成型为基础，从产业化的角度对HBP型成型机进行了液压系统和成型部件的改进设计；同时采用了二级预压机构，使该成型机的生产率达到 500kg.hd；单位能耗 60kwh。上'左右，磨损件修复周期 300小时左右，基本解决了影响生物质固化技术在国内推广的技术难题。

Flame retardants can be used in plastics,woods,paper products,and fabrics.

更多降低材料的燃烧性，减少烟雾和有害气体的排放。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷