熔融

The differential eguations and boundary conditions are established, based on these hypotheses. The theoretical formulary about sample atom number with different diffusion coefficient are reasoned out; the relationship between the isotope abundance ratio and the sample wastage of melting and solid samples and the samples simultaneously at evaporation and decomposition are discussed in theory.

根据这三条假设建立了样品原子数的微分方程及边界条件，推导出了不同扩散系数的样品原子数的理论公式，从理论上讨论了熔融态、固态样品以及蒸发分解同时发生的样品同位素丰度比与样品消耗量间的关系。

The performance of the electrochemical oxidation of the activated carbon in the carbonates was investigated.

研究了活性炭粉在熔融碳酸盐中的直接电化学氧化性能。

AJS (Air-pressure Jet Solidification) system is developed using the principles of FDM technology, but compared with traditional FDM machine there are some differences. So hardware structure, software module and control system need re-designing and optimizing.

气压式熔融沉积系统是在FDM技术原理的基础上开发出来的，但与传统的FDM快速成型机也有一定的区别，因此在硬件结构、软件模块、控制系统上需要重新设计和优化。

Melt aluminous park constant inside the mouth electric induction furnace of high temperature.

将熔融铝置于一个恒定高温的开口感应电炉内。

Rather than having the sample dissolved and introduced via a nebulizer and a spray chamber into the ICP, the laser is ablating the sample and a carrier gas transports the ablated material to the ICP.

激光器熔融样品，并通过运载气体将熔融的样品物质传送到IP，而不是将样品溶解后，通过雾化器和雾化室将样品传输给ICP。

At room temperature thermoplastic plastic usually granular, after heated to a certain temperature molten state, while its cooling after Curing, if it will become once again heating molten state, and the plastics can be re-forming.

热塑性塑料在常温下通常为颗粒状，加热到一定温度后变成熔融的状态，将其冷却后则固化成型，若再次加热则又会变成熔融的状态，而可进行再次的塑化成型。

Thermoplastic plastic usually get granular at normal temperature , after heated to a certain temperature molten state, while its cooling after Curing, if it will become once again heating molten state, and the plastics can be re-forming.

热塑性塑料在常温下通常为颗粒状，加热到一定温度后变成熔融的状态，将其冷却后则固化成型，若再次加热则又会变成熔融的状态，而可进行再次的塑化成型。

The decomposed temperature increases and the glass transition temperature decreases as the molar ratio of MA rises. The copolymer molar containing 30% of MA melts at approximately 188℃, which is significantly lower than the decomposed temperature. This copolymer is melt processable and is a potential material for the manufacture of PAN fibers.

含MA30mol%的共聚物的分解温度为338.8℃，而熔融温度仅为188.8℃，由于第二单体MA的加入，使得共聚物的熔点降低至分解温度之前，这为改性聚丙烯腈的无增塑熔融纺丝提供了可能性。

Microsilica silica fume and micro-production processes is the difference from natural quartz silica (SiO2) or fused silica (natural quartz at high temperature melting, after cooling the amorphous SiO2) by crushing, ball milling , flotation, acid purification, high purity water treatment by multi-channel processing of the powder.

硅微粉与微硅粉的生产流程上的差异硅微粉是由天然石英（SiO2）或熔融石英（天然石英经高温熔融、冷却后的非晶态SiO2）经破碎、球磨、浮选、酸洗提纯、高纯水处理等多道工艺加工而成的微粉。

The Raman spectral bands indicated that the damage of the heating on the DNA conformation is limited below the melting point. The damage of the DNA molecular structure increased with a rise in temperature above the melting point. The damage was first obversed in adenine and deoxyribose.

研究结果表明，在熔融温度以下热处理对DNA构象的影响是轻微的，在熔融温度以上则随温度的升高，对DNA分子结构的影响及破坏也逐渐加剧，首先受影响的是腺嘌呤和脱氧核糖。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。