熔点

The melting point of Zirconium Silicicate is high: 2500 degrees Celsius, therefore the fire-proof material, casting material and spray coating foresees of glass kiln stove are also widely applied.

硅酸锆的熔点高：2500摄氏度，所以在耐火材料、玻璃窑炉浇注料、喷涂料中也被广泛应用。

The conductive pole only acts for contact and conducting during welding, the pressure pole in its center forces pressure under action of compression spring, and the pressure pole is characterized by high fusing point and mechanical intensity because of the tungsten alloy material, and the life length of contact finger is prolonged.

在焊接作业时，导电杆仅起到接触导电作用，而其中心的压力杆在压簧的作用下起到施加压力的作用，由于压力杆采用钨合金材料，具有高熔点、高机械强度的特点，不会变形，导电杆压力小不易变形，从而延长了整个触头的使用寿命，并且焊点整齐美观。

Nanocrystalline hexagonal VSi〓, with an average diameter of 35nm, was prepared via a reduction-silication route by the reaction of metallic sodium with vanadium tetrachloride and silicon at 650℃ in a molten salt system of magnesium chloride and sodium chloride. The sample had good oxidation resistance at 1000℃.

金属硅化物通常具有很高的熔点、较低的电阻率、很好的高温热稳定性，有些还具有奇异的光、电、磁、超导、催化等性能，因此是一类最富潜力的高温结构材料和电子材料。

The results show that HDPE pipe prepared by vibration extrusion has higher crystallinity, higher melting temperature, larger lamellar thickness, larger crystal size, and more perfect crystals, and the slow crack growth resistance of HDPE pipe is improved.

结果表明：振动挤出的HDPE管材结晶度提高，熔点升高，晶片变厚，晶粒尺寸变大，结晶完善，耐慢速裂纹增长性能提高。

An advanced method of producing Al3Ti／Al composites, self-propagating high-temperature synthesis in an Al melt, is described.

介绍了高熔点化合物颗粒增强的铝基复合材料的一种先进制备方法，即自蔓延高温合成法，并以Al3Ti／Al为例进行了实验研究。

While modern commonly used thermoplastic rubber is different, such as EVA hotmelts, it's a solid lead-free moisture can be self-fluxing materials, the use of this material to pass the appropriate melting point of temperature, temperature, opening hours, setting time and cooling hardening time, then by a workholders correctly, can achieve a reliable bond.

而现代常用的热塑性胶就有所不同，如EVA热熔胶，它是一种固体的无水分的可熔性胶粘材料，使用这种材料要通过适当的熔点温度、使用温度、开放时间、固化时间和冷却硬化时间，再经正确的夹紧定型，才能达到粘结的可靠效果。

Self-fluxing, and the spray wetting of the fine, and relatively low melting point, spray welding layer has high hardness, corrosion resistance, wear-resisting, heat-resistant characteristics of iron content higher than the cutting HQ.

自熔性、润湿性和喷焊性优良，而且熔点比较低，喷焊层具有硬度高、耐蚀、耐磨、耐热特点，含铁量高于HQ。

Self-fluxing Fe-Cr-Ni-B-Si alloy prowders are laser clad on medium carbon steel substrate of dimensions 80×35×10mm〓. The investigation results of this clad layer are: micro-defects, micro-cavity and occluded forin substance, are the micro-cracks and crack resourses in clad layer; crack of coating propagates along the boundary of two kinds of eutectic sutructure; The included angle θ between the cracking direction and laser scanning direction in multitrack overlapping clad is smaller than that in one-track clad because of crack propagating along crystalline growth direction and crystalline direction in overlapping zone being different from it in one-track clad.

在调质态的45〓钢表面，采用预置粉末法进行FeCrNiBSi合金的多道搭接激光熔覆，对其熔覆层进行分析表明：多道搭接激光熔覆层裂纹扩展方向与激光扫描方向间的夹角θ与单道熔覆时相比明显变小，前者θ0°，后者θ角基本都为90°，这主要是因为多道搭接时，搭接区结晶方向发生了变化以及裂纹沿结晶方向扩展所致；激光熔覆层裂纹大多是以覆层与基材交界面的孔洞、熔覆层内不同方向共晶团间的显微缩孔、夹杂物的边界等三种显微缺陷作为裂纹源，并沿低熔点物相形成元素偏析造成弱化膜的共晶团界面扩展延伸。

The results as below: 1 The extracting rate, melting point and saponification value of refined beeswax were 91.13%, 63~69°C, 107.77 mgKOH/g respectively.

结果表明：(1)原料粗蜂蜡精制后的得率为91.13％，精制蜂蜡的熔点为63～69℃，皂化值为107.77mgKOH／g。

Extracting oat oil with aceton,petrobenzine,ethano-aceton and n-hexne from oat,determining quality of physical and chemic about acidity value ,iodic value,saponification value,unsaponification,colour and melting point,analysis on composition of fatty acid on oat oil.

分别以乙醚、丙酮、丙酮-乙醇、正己烷对燕麦进行萃取，对所得油脂进行酸价、碘价、皂化值、不皂化物、色泽、熔点等理化性质的测定，同时对燕麦油的脂肪酸组成进行分析。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失