熔渣的

A large amount of anorthite formed in the slag lumps is the main reason of slag blockage in the Shell gasifier.

大量钙长石的生成是导致安庆石化Shell气化炉产生大块熔渣和堵渣主要原因。

He influence of other factors on slag detachability is related to the microstructure of slag.

iO〓/SiO〓比值是通过影响熔渣微观组织结构而影响脱渣性的。

Physical and chemical properties of industrial slag containing TiO2 is analyzed,and material properties of the fettling mix for converter such as density,strength,high-temperature stability and slag corrosion resistance are studied afrer adding industrial slag containing TiO2 into fettling mix for converter .

分析了含TiO2工业渣的物理化学特性，研究了在耐火补炉料中加入含TiO2工业渣后对材料的体积密度、强度、高温体积稳定性、抗熔渣侵蚀等性能的影响。

The volatility and melting uniformity of premelted fluxes and mixed powder was studied mainly on fluoric slag for steelmaking of m...

本文以连铸保护渣基料及CaO-CaF〓基炉外精炼渣两大炼钢含氟渣系为主，对预熔型和混合型两种形态渣的挥发性和熔化均匀性进行了研究。

The volatility and melting uniformity of premelted fluxes and mixed powder was studied mainly on fluoric slag for steelmaking of mould powder base and CaO-CaF〓 based refining slag in the paper.

本文以连铸保护渣基料及CaO-CaF〓基炉外精炼渣两大炼钢含氟渣系为主，对预熔型和混合型两种形态渣的挥发性和熔化均匀性进行了研究。

The reoxidation mechanisms of IF steel containing Al and Ti by reducible oxides in the slag were analyzed. A model of predicting total oxygen in the molten steel was established based on the reoxidation mechanisms. It was found that two different reaction mechanisms existed when and in the slag reoxidated the molten steel.

分析了IF钢冶炼过程中渣对钢液中、的氧化机理，在此基础上提出了IF钢加铝脱氧后全氧的预测模型结果表明，熔渣中、对钢液的二次氧化存在两种方式。

The phenomena of slag entrapment into metal bath and fluid flow near the slag-metal boundary are studied experimentally by use of a two-component LDA and a high speed camera.

本文应用激光测速和高速摄影等方法对反应器中熔渣卷入金属液和渣铁边界附近的流动现象进行了模拟研究。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

Slag viscosity has been tested by viscometer, slag mineral structure has been observed by microscope of high magnification. First discover that UPC is favorable to weeping and taking shape of high titanium-bearing slag, put forward that the mechanism of titanium slag adhering coke is that TiC、TiN and the carbon of coke which is regard as C〓、C〓、 C〓 shape et al weld into chemical bonding compound.

首次发现UPC有利于高钛渣的形成和滴落，提出了钛渣润湿焦炭的机理是碳以C〓、C〓、C〓等形式与TiC、TiN结合成了强力键化合物及固熔体，粘附在焦炭表面的TiC、TiN层随焦炭下降至风口区被再次氧化，而不会大量弥散于渣中影响其粘度。

The formation process of furnace wall slag flow was described and the particle deposition model was established according to the characteristics of slag tap gas boiler, simulation results are consisted with experimental data.

根据液态排渣气化炉本身特点，描述炉壁熔渣流的形成过程，建立适用于液态排渣气化炉的颗粒附壁沉积模型，模拟结果与实验值吻合较好。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失