焊的

"Both primary and mating ring are made of solid-block construction for greater reliability and longer service life compared to the soldered, welded or sprayed hard-face designs used by other manufacturers."

与其他制造商所采用的低温焊接、熔焊或喷射硬面设计相比，主密封环和配套密封环均采用固体单元结构，可靠性更高，使用寿命更长。

"Both primary and mating ring are made of solid-block construction for greater reliability and longer service life compared to the solder ed, welded or sprayed hard-face designs used by other manufacturers."

与其他制造商所采用的低温焊接、熔焊或喷射硬面设计相比，主密封环和配套密封环均采用固体单元结构，可靠性更高，使用寿命更长。

"Both primary and mating ring are made of solid-block construction for greater reliability and longer service life compared to the soldered, welded or spray ed hard-face designs used by other manufacturers."

与其他制造商所采用的低温焊接、熔焊或喷射硬面设计相比，主密封环和配套密封环均采用固体单元结构，可靠性更高，使用寿命更长。

Both primary and mating ring are made of solid-block construction for greater reliability and longer service life compared to the soldered, welded or sprayed hard-face designs used by other manufacturers.

与其他制造商所采用的低温焊接、熔焊或喷射硬面设计相比，主密封环和配套密封环均采用固体单元结构，可靠性更高，使用寿命更长。属类：-〖水泵

The statistical natures of FCP at the weld toes were investigated on the probability space.

在概率空间上研究并初步揭示了焊趾疲劳裂纹扩展过程的统计规律。

The expatiation of the control function in this article is divided into two sections: the manufacturing execution system and the basic automatic control. The former was focused on the quality assurance system of pipe welding and the quick-setting system,and the later focused on the control functions,such as the roll gap position control, the tracking of cross-welding line between coils,the sequence control, the speed control over the main driver, edge miller, cut-off machine, HF welder and the heat treatment of weld seams.

分制造执行级MES 和基础自动化级两部分阐述控制功能，MES方面着重介绍快速设定系统和焊接质量保证系统；基础自动化部分重点介绍辊缝位置直控制、钢卷对接焊缝跟踪、顺序控制、主传动速度控制及铣边机、飞锯、高频焊机、焊缝热处理等单体设备的控制功能。

Consequently, it is recommendable to cancel the operation of post-welding heat treatment.

试验结果表明，传统的焊后热处理工序应当取消。

These cracks occurred at either the beam flange or in the column flange depending on the reentrant corner weld angle.

这些裂纹视凹形焊角的不同，或者出现在横梁翼缘上，或者出现在立柱翼缘上。

The same 30 ℃safety margin brings the maximum reflow temperature to 260℃.

同样的安全余量30℃最大峰值再流焊温度260℃。

The most obvious is the necessity for increased reflow temperature.

最明显的是，使用无铅锡膏必须提高回流焊温度。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。