焊的

Equivalent stress nearby the spot weld is greater other placeand there is obvious stress concentration.

由应力分布情况得出，在焊点附近的等效应力较大，存在明显的应力集中现象，同时由于折流缝焊的存在，增加了波面传热板强度。

The quality assessment of brazed joint of aluminum matrix composites was performed by the advanced ultrasonic imaging technology .

超声成像技术能反映出铝基复合材料钎焊界面的接合状态，可检测出气孔、氧化膜夹杂和未钎透缺陷，为铝基复合材料钎焊的研究提供了有效的检测手段。

Our Real-Time Robotic Control System for Titanium GMA W will consist of sensors for measuring characteristics of the weld, the arc, and the droplet formation and transfer and use these data to adjust the weld current, voltage, and speed.

我们用于钛合金气体金属电弧焊的实时机器人控制系统将由用于测量焊接特性、电弧、焊珠形成和移位的各种传感器组成，利用这些数据对焊接的电流、电压和速度进行调整。

Temperature distribution,deformation and residual stresses of thick plate butt multipass welding were researched through a comparison among normal welding, vibratory welding and welding with wind cooling.

采用振动焊接及气冷的方式与常规焊接对比，研究了埋弧自动焊厚板角接多道焊的温度、变形及残余应力。

After laser order scan research, some new assume are advanced on order distributing of grit in brazed monolayer diamond wheel.

在激光有序扫描钎焊的基础上，提出了有关钎焊金刚石砂轮磨粒有序的一些新设想。

Simulation of DC flash butt welding by coupling with electricity, heat, and mechanics will be instrumental in designing and drawing out technical specification.

本文首先采用有限元模拟方法对超细晶粒钢直流电阻闪光对焊的焊接过程进行了研究，建立了直流电阻闪光对焊过程的电、热、力耦合模型。

The experimental results showed that for fusion welding, the vacuum arc is possessed of good stiffness, strong penetration and a good appearance of weld on both sides.

主要研究真空条件下的自持放电电弧作为新型热源用于熔化焊及钎焊的工艺适应性。

Fracture often occurrs in the weld joint of the wire during drawing. Drawing fractures morphology were investigated and classified.

由于现代化大生产的连续性，不同卷盘条通常采用电阻对焊的方法连接在一起，在生产过程中盘条电阻对焊区域容易出现拉丝断裂。

Analysis of the influence of laser welding speed on the shaping and quality of weld seam was carried out.

测量了激光对接焊后热轧钢板正背表面焊缝宽度，分析了激光焊的焊接速度对热轧钢板焊缝成形和质量的影响。

For the reasons, Ukraine Paton Welding Institute puts forward the method of A-TIG welding.

针对TIG焊的不足，乌克兰的Paton焊接研究所首先提出了A-TIG焊方法。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐