焊接

Used for welding heat-resistant stainless steel 0Cr26Ni21, Cr steel and different type of steel under high temperature.

用於在高温条件下工作的 0Cr26Ni21 耐热不锈钢及铬钢、异种钢的焊接。

Housing fabricated from carbon steel and is fully welded to provide a hermetic seal.

房屋的碳素钢制成，完全焊接提供密封产品。

So far, the yield of hermetical welding for large cavity devices (perimeter: 150 ～ 200 mm, diagonal:≤70 mm) reaches 93%?

目前，大腔体器件(150～200mm周长，对角线≤70mm)气密性焊接的成品率已达到93%。

All models are of welded stainless steel construction and are hermetically sealed.

所有温度计均可用于不锈钢焊接制造和密封件制造。

Herrmann Ultraschalltechnik, founded in 1961 in Karlsbad Germany by Walter Herrmann became over the years the Technology leader in Ultrasonic welding.

由瓦尔特。海尔曼于1961年在德国卡尔斯巴德建立的海尔曼超声波技术有限公司一直是超声波焊接领域的技术领先者。

Development of laser beam welding of high strength aluminum alloys .

李睿。 6063铝合金型材焊接性能的研究。

Two high-tension line to be welded in two electrodes, or else there will be bad due to corrosion, effects.

两根高压线必须焊接在两个电极上，否则会因腐蚀出现接触不良，影响效果。

The welding equipment are advanced OTC,CO2,gas shielded arc welding and automatic submerged arc welding,semi-automatic cutting machine,250 ton liquid press,hobber and plate cutting machine.

焊接设备采用先进的OTC、CO2气体保护焊和埋弧自动焊、半自动切割机、250吨油压机、滚床设备、剪板机等。

Part of the normal roller, the fault is not resolved, check for roller pressure, which can use FUSE (electrical purposes 20, fusealways) and qianyanzhou hobber in rolling direction, not to mention the occipital clearance to unload their plates and blankets, the slot for the Department in the roller snthase pad, if rolling pillow gap over specification number, the adjustment of the diaphragmless, the pillow are met at both ends of the clearance requirements, you can troubleshoot.

墨辊局部变态了，障碍仍未处置，再查抄滚筒之间的不张力，可用电工用不焊接丝（20号保障丝）和千分卡轧测滚枕间隙，必须卸下印版和橡皮布，在滚筒的不满档处分不抬轧测，若滚枕间隙超功表明书规矩的数值，则调动调不抬器，使滚枕两头间隙都相符表明书上的请求，即可摈斥障碍。

Squeezing and preparing a plate underframe and a upper holdfast with support legs respectively, pre-sintering and final finishing the underframe and upper holdfast respectively, then welding the underframe and the upper holdfast of upper holdfast into one unit, finally heat treating the welded one unit product under the temperature of 150-650DEG C.

分别挤压制成一个平板形底架和一个带有支撑腿的上支架，将底架和上支架分别预烧结、精整，然后，再将底架和上支架的支撑腿烧结焊成一体，最后在150～650℃的温度下将焊接为一体的产品进行热处理。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失