焊接

The res ults of arc-starting and welding tests for titanium alloy are also presented in detail in the paper . Tensile strength of welding joints has reached the demands of we lding standard, esp. no spatters on back weld are obtained in contrast w ith EBW.

文中详述了空心阴极焊枪设计、引弧试验情况及钛合金焊接工艺试验，结果表明焊接接头拉伸强度达到标准的要求，特别是与电子束焊相比，焊缝背面无焊接飞溅。

In electronic engineering, we usually have to bond a micro-strip board to a metalcarrier in order to provide proper stiffness, thermal conductivity and electrical conductivity, thus to make general handling,solder stencilling, pick and place of components be easier, and prevent the warping or distortion of the board during soldering.

林伟成，微带板与金属载体间的大面积焊接及胶接方法工程中常常需要把微带板和金属载体焊接或胶接起来，以获得合适的刚性、电导率和热导率，从而使丝网印刷、元器件贴装等工艺过程变得更加容易。并防止焊接过程中微带板的翘曲和变形。

At the same time, the characteristics of the microstructures of the laser welds and HAZ were analyzed.

对于不锈钢的激光焊接，发现在相同条件下，用YAG激光焊接，得到的焊缝熔深比用CO〓激光焊接时的大10％-30％，宽度值则小10％-20％。

It greatly reduces the noise from the discontinuous spectrum in the arc and adapts to the seriously fluctuating welding current during the process and obtains the clear images of the welding pool using common industrial CCD camera.

在对铝合金焊接光谱分析的基础上，以焊接电弧光中的连续光谱作为光源，采用宽带滤波方法设计的全新的光学图像传感器，利用普通工业CCD摄像机获得了画面清晰、质量稳定的铝合金焊接熔池区域图像。

Through collection of TIG welding arc light spectrum of steel with disturbing factor,this paper studied the effect of disturbing factors such as rusty and various gas flow rate on the arc light spectrum distribution.Furthermore, the light radiation of different spectral zones was studied to get the spectral signals that could reflect the disturbing factors which were critical for online welding quality control.

通过对干扰因素下TIG焊电弧的光谱信息进行采集，研究了气流量变化、焊接试件表面存在锈等干扰因素对焊接过程电弧光谱分布的影响，并基于光谱分布的分析，进一步探讨了不同光谱谱段对干扰因素的反映，寻求实现焊接过程质量在线光谱测控的理论依据。

ABSTRACT The research of metal transfer in metal gas arc welding is of great significance for the control of arc welding process and quality, the improvement of existing welding technology and the development of new welding equipment. With the powerful aid of welding arc spectrum which contains plenty of information of metal droplet transfer, this dissertation, which mainly aims at putting forward an effective detecting method with arc spectrum signal, has inspected the spectrum of metal gas welding arc and discovered their dynamic characteristics of each kind droplet transfer mode.

熔化极气体保护焊熔滴过渡的研究，对于焊接过程及质量控制、焊接工艺方法的改进和新型焊接设备的推出都具有重要意义，而熔化极气体保护焊电弧光谱中含有丰富的反映熔滴过渡的信息。

Distribution features for TIG welding arc ultraviolet spec tr um associated with various of welding parameters have been acquired, and inform ations of welding arc ultraviolet spectrum also have been analyzed.

针对焊接电弧紫外光谱信息的研究，研制了一套焊接电弧紫外光谱计算机采集和处理系统。利用此系统对TIG焊电弧紫外光谱进行了研究，成功地获得了不同焊接规范下的电弧紫外光谱频谱分布特征，并对此进行了分析。

Based on the theory of magneto-hydro dynamics and real welding conditions,a three-dimension united mathematical model of TIG welding arc and weld pool was established.

根据磁流体动力学理论以及焊接的实际情况，建立了三维TIG焊接电弧与熔池的统一数学模型，避免了对电弧以及熔池界面条件的假定，使得对焊接电弧与熔池行为的分析与实际情况更近了一步。

The reasons of welding distortion for the bottom plate of large sedimentation cupboard is analyzed.

对大型沉降槽底板焊接变形的原因进行了分析，并提出了合理的安装和焊接顺序，有效地控制了槽底的焊接变形。

This paper using the FEM software Marc, for the 50 and 60 degree V groove of flat plate butt joint simulate the one-layer and three layers welding, finish each welding and cooling it down to room-temperature then start the next welding true represent process and get the temperature field, residual deformation and welding residual stress, according to the theory analysis and empirical equation verified the temperature field and residual deformation all correct, comparison with experiment verified the welding residual stress regularity and correctly.

本文利用有限元软件Marc，对开60°和50°V型坡口的平板对接接头，动态的模拟了单层单道打底焊，焊完一道后让试件冷却到室温以及单层单道满焊，每焊完一道后让试件冷却，然后再焊下一焊道，道间温度≤200℃，在以此为初始边界条件下开始下一道的焊接，真实的再现了焊接过程，得出了温度场，残余变形和残余应力场的分布规律，根据理论分析及经验公式验证了温度场以及残余变形的正确性，角变形的大小，这些结果与数值计算相吻合。通过与实验测得的残余应力进行比较，验证了焊接残余应力的分布规律及模拟的正确性。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。