热的产生

The result shows that the combustibility of plasticpillion and shell of the motorcycle is the main factor in theburning. The heat release rate and temperature profile of the motorcycle with an iron-shell is much lower than a motorcycle with plastic pillion and shell.

由试验结果发现，125c.c 塑胶壳机车之座垫与塑胶外壳燃烧所产生的最大热释放率峰值分别为619.0kW 与1268.0 kW ，总发热量为68.49MJ 与210.0MJ ，而单辆机车内所有塑胶材料之发热量约占机车整体可燃物发热量的71.2%，为机车燃烧之主要危险因子。

To compensate for thermal expansion and deformation due to the vacuum compact compensators are provided for 100 and 150 mm diameter pipework.

为补偿因真空产生的热膨胀和变形，可提供适用于100-150mm管径管路的紧凑型补偿器。

It includes high power high voltage constant-current-charging system, capacitors bank, discharge control system, power supply of preignition for Xe-flashlamps, general control and diagnostic system. The power conditioning system drives flashlamps that pump the SSHCL. Flashlamps are driven by high voltage Silicon Controlled Rectifiers switched, resonant charged, discharge pulse forming network. The system uses microchip and digital circle which is based on CAN-bus for control and diagnostics. Energy diagnosis and thermal management are controlled by computers.

其中大功率高压恒流充电装置采用了L-C串联谐振电路，充电功率大，效率较高；储能装置采用了多节脉冲成形网络，可产生波形良好的强电流放电脉冲；放电控制装置采用高压大功率晶闸管，开关速度快，工作稳定；预燃与触发装置采用了开关电源电路，效率高、功耗小；总控与测量装置采用基于CAN总线的数字电路和单片机技术，控制冷却系统在激光器出光时对脉冲氙灯进行水冷，并对全系统进行控制和状态检测，同时具有过压、过流、过热等保护功能。

In the process of coal pyrolysis, the product of tar causes a lot of problems for normal system operation.

摘 要：煤在热解和气化过程中产生的焦油，影响系统的正常运行。

Based on complex transfer matrix method,a model to calculate unbalance response of a residual bending rotor is set up.Response of different residual bend mode is analyzed.

0前言转子由于加工误差以及热变形等众多因素的影响，经常会产生一定的弯曲量，引起转子振动。

Measuring conditions were analyzed,such as lamp current,slit width,air and acetylene flow.

铜是钢中的有害杂质，能使钢产生热脆性，破坏钢的焊接性能。

The results of tests showed that even the Sugi square lumbers ware difficult to be dried, the better drying quality especially with less checks will be reached if some special pre-treatment methods were taken before the RFN drying, such as, steaming and superheated-steam pre-treat on Sugi lumbers; another, make kerf along the length direction of lumber before the drying.

结果表明，柳杉髓心方材虽难干燥，但在高频真空干燥前对木材进行合理的处理，例如：蒸汽和过热蒸汽预处理：沿木材长度方向制作一定深度和宽度的切口等，都可有效地提高干燥质量，尤其可减少开裂产生。

In order to reduce the internal stress of wood during drying, an attempt was made to dry wood with superheated steam above 100°C.

为减小木材干燥过程中产生的内应力，本研究尝试在100℃以上的高温高压过热蒸汽条件下对木材进行干燥。

In the second part of the article, an endocellulase from culture supernatant of a thermophlic fungus C.

本研究第二部分主要探讨了液体发酵嗜热真菌Chaetomium thermophile产生的内切β-葡聚糖酶的分离纯化及特性。

However, caffeine's role in thermogenesis probably isn't enough to result in significant weight loss.

生热作用是你的身体通过消化食物而产生热量和能量的方式之一。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。