热电偶

Main thermocouple thermometer, direct-reading air permeability tester, mold and core sand experimental apparatus, such as ultrasonic flaw detector.

主要有热电偶测温仪、直读透气性测定仪、型芯砂实验仪器、超声波探伤仪等。

Thermocouples shall be attached to the test alcove where the highest temperatures are likely to occur, including

将热电偶装在测试橱柜上最高温度有可能出现的地方，包括

In this paper,the drag-reducing surfactant solution flows in a fully developed turbulent channel flow have been analyzed experimentally using Phase Doppler Anemometry and thermocouples in order to study the temperature fluctuations and heat transfer characteristics on the drag-reducing and heat transfer reduction phenomena of the surfactant solution flows.

该文针对在水中添加阳离子表面活性剂产生的减阻作用同时降低传热性能的现象，应用相位多普勒激光测量系统和热电偶温度测量系统对二维流道内表面活性剂减阻流体热边界层内的湍流温度脉动以及传热特性进行了实验研究。

In this paper, the design of the system, including thermocouple sensors, cold junction compensation system, SCM interface, application program Signal filter and other processing, is be detailed analysis and explanation.

本文对该系统的设计，包括热电偶传感器、冷端补偿系统、单片机接口及其应用程序以及信号的滤波处理等进行了详细的分析和说明。

This paper is major in the research of PROFIBUS-DP protocol and SPC3s kernel program, and gives the hardware and software architrave. The measurement system can not only get the exact data from location but also has the function of self-diagnosis、 self-alarming and self-compensation.

本论文在研究了PROFIBUS-DP现场总线的基本理论的基础上，通过对协议芯片SPC3的资源和通信协议的研究，剖析了SPC3的核心程序，探讨了装置组成的硬件和软件策略，给出了硬件软件系统设计框图，开发出带PROFIBUS-DP接口的热电偶温度检测装置。

Calibration of the muffle furnace may be carried out using an appropriate digital temperature meter and a working thermocouple probe calibrated against a standard thermocouple traceable to the National Institute of Standards and Technology.

进行马弗炉的校准，可以使用一个适当的数字温度表和一个工作热电偶探测器，该探测器须使用能够追索到国立标准和技术研究院（National Institute of Standards and Technology）的标准热电偶进行校准。

Two different methods of in—process monitoring grinding temperature, that is graphite—treated wheel—— workpieces thermocouples and wheel with wire bedded in——workpiece thermocouples, were created.

通过综合比较目前已有的磨削烧伤预报方案的优缺点，指出磨削过程中直接检测磨削温度以预报烧伤应该是烧伤预报的最佳方案，因此，针对性探索了两种适用于生产现场检测磨削温度的新方法，即渗渍石墨砂轮——工件热电偶法和砂轮埋丝——工件热电偶法。

This paper combines the Fieldbus and traditional thermocouple temperature instrument technique to design a thermocouple temperature measurement system of Fieldbus.

本论文将先进的总线技术与传统的热电偶检测装置相融合，提出基于现场总线方式的热电偶温度检测装置的设计新思想。

By analyzing the characteristic features of the variations of temperature in the workpiece surface layer during grinding and the thermal inertia of the thermocouple , this paper reviews the reliability of the method recommended by Koya Takazawa of the dynamic temperature measurement by means of the single-wire thermocouple , and presents a method by which the dynamic response ability the instrument for temperature measurement should possess may be approximately evaluated according to the grinding ...

本文通过分析磨削时工件表层温度的变化规律以及热电偶的动态响应能力，对高泽所推荐的单丝热电偶动态测温方案的可靠性进行了论证，并在此基础上提供了有关平磨钛合金与45~#钢时的磨削力与工件表层内部温度分布的实测数据。

We installed 20 pairs of thermopiles between the sample holder and the copperheat sink, and 5 pairs of thermopiles between the copper heat sink and inner radiation shield respectively for sample adiabatic.

c。为了保证与环境绝热，在样品架与铜块之间安装了20对热电偶，同时还在铜块和内辐射屏之间装了5对热电偶来监视样品与环境的温差，以便于自动加热控温。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。