热电偶

Traditionally this was done with a carefullyconstructed ice bath (hence the term 'cold' junction compensation).Maintaining a ice bath is not practical for most measurementapplications, so instead the actual temperature at the point ofconnection of the thermocouple wires to the measuring instrument isrecorded.

传统的做法是把该结点放置在冰水融合物中采用冰水融合物并不是对大部分的测量设备和应用场合都是适用的，所以需要把热电偶与测量设备的连接点温度记录下来。

The temperature-monitoring instrument for optical fiber transmission high- voltage switch contact point developed by this project has been conducted pilot testing in Sichuan Electrical Facilities Corporation and Gansu Tianshui Electrical Facilities Plant. Rectified by a standard .thermocouple temperature-measuring instrument, the testing results in situ showed that the temperature-monitoring instrument has fast response speed, accurate location for temperature arising over set limit, small measurement error within ?

本课题所研究的光纤传输高压开关触头温度监测仪分别在四川电器股份有限公司和甘肃天水电器厂进行了现场实测，并采用热电偶测温仪校验，实测结果表明：该温度监测系统反映速度较快，温升越限定位准确，测温精度误差在±1℃以内，具有较高的可靠性、安全性和经济性。

It has the advantages of simple structure, easy fabrication, high recovery coefficient, short response time and spot temperature measurement etc.

总温热电偶具有结构简单、制作简便、温度恢复系数高、响应时间短、能测量点温度等特点，更适用于测量高焓高速气流总温。

The contact measurement of infrared transferring signal was realized with temperature signal of thermocouple of infrared communication.

红外传送信号的接触测量通过红外通讯传递热电偶的温度信号。

This paper discusses the conception of a carry-home high precision temperature equipment verification device based on a MSC1210 single chip computer. The device samples temperature signal by temperature sensor, standard platinum resistance and thermocouple, and realize multi-channel temperature meterage by controlling relay switch. The result be sent and displayed on LCD.

本课题研制出一种以MSC1210单片机为核心的便携式高精度温度试验设备检定仪，它以标准铂电阻和标准热电偶为传感器，通过控制继电器实现对温度试验设备的多通道循环温度测量，测量结果转化为温度值后由LCD显示。

The hardware of intelligent temperature controller based on ARM single-chip microcomputer was designed with the K-type thermocouple and MAX6675 as a temperature detection circuit, and a solid-state relay as a temperature control element. The main circuit was controlled using the switching characteristics of the solid-state relay t.

以ARM单片机为核心，设计并分析了电阻炉智能温度控制系统硬件电路，由K型热电偶和数字转换芯片MAX6675组成温度检测电路，采用固态继电器来作为温控元件，利用开关特性来控制电路的断开和接通炉温控制主电路。

A Talysurf was used to measure the surface roughness of the ground surface.

采用热电偶和三向测力仪分别测量了不同磨削条件下接触区的温度和力，并使用电子扫描显微镜和表面轮廓仪对已磨表面形貌和粗糙度进行了观测。

The domestics for backup roll bearing temperature control system of imported aluminium sheet and foil mill have been carried out.

介绍了铝板轧机支承辊轴承控温系统热电偶补偿导线的国产化；铝箔轧机支承辊轴承控温系统国产化。

Control panel has temperature controls and digital thermocouple readout with four-position selector switch.

控制面板有温度控制和数字热电偶读出四个位置选择开关。

Aiming at the corrosion problem of thermocouple used in high temperature salt bath furnace ,this paper has done an experiment on the cathodic protection.

本文针对高温盐浴炉热电偶直接测温的腐蚀问题，进行了阴极保护试验，分析了腐蚀速度随保护电流密度的变化关系。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。