烧结的

In KP1 type perforated brick masonry, expansion bolt especially design for perforated brick is prefer, because it can form "self- anchor" effect and hold tightly in brick hole.

KP1型矩形条孔烧结页岩多孔砖砌体墙上应采用空心砌体专用膨胀螺栓，因其能够形成可靠的"自螺母效应"。

In 1950 the ferrous burden composition consisted of 20% sinter and 80% lump ores and others.

在1950年，ferrous burden的组成包括20%烧结，成块矿石及其他占80%。

There are three time sections for SiC-Si3N4 firebrick processing in electrical resistance furnace, which is called heating, chemical reaction-sintering and cooling section.

电窑中SiC-Si3N4耐火砖的烧制过程按时间可分为三个阶段，即加热阶段、化学反应－烧结及冷却阶段。

As the arrival time of a flexion is known, the average speed at the forefront can be calculated.

根据拐点出现的时间，求出烧结过程中各带前沿平均速度。

Therefore, these results prove that crystal formation interferes with the sintering process of a crystalline frit.

所以这些结果证明晶体结构干扰结晶弗里茨的烧结过程。

Good corrosion resistance ,antioxidation and thermal shock resistance. They are suitable for petro-chemical industry (like large and medium sized synthetic ammonia vaporization furnace and gasometry ) and metallurgical industry (for example , the bottom of roll steel heating furnace , steel spout , various kinds of high temperature furnace and ceramic sintered furnace). Also can be used as auxiliary material in high temperature industry like kiln furniture like pusher.

制品具有耐高温、耐腐蚀、热震稳定性好等特点，适用于石化工业、大中型合成氨气化炉与造气炉及轧钢加热炉底、出钢槽、各种高温电炉、钼钨丝高温炉、陶瓷煅烧炉、氧化铝瓷烧结炉等，也可作高温中的辅助材料，如匣钵、窑车砖等。

The cathode assumes a rather satisfactory structure and has a good oxygen reduction zone in sintered at 1000℃.

在1000℃烧结温度时，阴极具有较好的微结构和氧还原反应区域

A new cermet sinter with through micro-porous structure was developed by vacuum liquid phase sintering method, in which Al2O3-Ni-Cr-Mo-Si-Fe powder was used as the basic material, TiH2 and CaCO3 were used as the composite pore-forming materials and hominess grains was used as dispersal particles. The cermet sinter was then infiltrated with Ag-Cu-Pb-Sn at vacuum and formed a new high temperature self-lubricating material.

以TiH2和CaCO3为复合造孔剂，以硬质微细颗粒为惰性弥散质点，采用真空烧结法制备出具有贯通型微孔结构的Al2O3-Ni-Cr-Mo-Si-Fe系金属陶瓷烧结体，并在烧结体中浸渍Ag-Cu-Pb-Sn系浸渍型固体润滑剂制备出新型高温扩散自润滑材料。

Through sedimentation experiment and hot-press sintering Ti-Mo FGM with smoothly varying composition was fabricated.

通过沉降实验和热压烧结技术，制备出了组分连续变化的Ti-Mo系梯度材料。

Pure LaNbO〓 ceramic has been prepared by hot-press sintering with the LaNbO〓 powders we synthesized.

以所制备的LaNbO〓粉体为原料，采用热压烧结工艺制备了多晶LaNbO〓陶瓷。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。