烧结的

The heat air sintering can increase the strength and reductibility of sinter provided that the decrease in total heat consumption on sintering is less than 10 percent.

在总热量消耗降低不超过10%的条件下，热空气烧结可以改善烧结矿的强度和还原性能。

The activation effect is proper when the Cu component is low, but it becomes weaker as Cu increases. This is probably due to that there is not dissolution and reprecipitation of W in liquid Cu during the process of liquid phase sintering.

含Cu量较少的粉末烧结W—Cu合金有一定的活化效果，但在含Cu量较高时，活化效果不十分明显，可能与烧结过程W不能在液相Cu中产生溶解—析出有关。

For BM 10h mixture, the structure has been characterized by nearly full laminarization in compact. The effect of mechanical activation is attributed to fining of powder grains, homogenizing of the blends, creating fresh surfaces, forming layer structure and intensifying dissolution and reprecipitation of Mo in liquiid Cu.

采用X射线衍射，微观电子显微术、EDXA和DTA热分析技术等实验手段，对混合元素粉末球磨过程颗粒变化、球磨粉末的烧结性能、活化机理、烧结合金组织与产品化工艺等方面进行了较为全面系统的研究。

In a previous project implemented by VAI, the sinter-strand length was extended by 18 m to increase the total sinter production.

之前，由VAI完成的工程，带式烧结机的长度已经增大到18米以提高总体烧结产量。

In this study, WCS was obtained by carbonizing wood material impregnated with PF resin without oxygen. The yield, properties, effect factors, microstructure of the products and the chemical reaction were analyzed.

本研究采用酚醛树脂浸渍木质材料，经过高温烧结制得木陶瓷产品，并对产品得率、性能、影响因素、微观结构以及烧结过程中的化学变化等进行了分析，并探讨了阻燃处理提高产品性能的可能性。

The formed body is degreased at a temperature having the formed body not sintered. A sintered body is provided by sintering the degreased body.

在不烧结成形体的温度使成形体脱脂，然后烧结已脱脂的成形体而得到烧结体。

In this paper, the two kinds of hot wind igniting and combustion-supporting technique were summarized.

通过对烧结机两种热风点火助燃方式的项目总结，简要介绍了烧结余热用于点火炉进行热风点火助燃的研究和实际效果。

He sintering of Ti/Al -Al_2O_3 powder in nm scale on SPS is composed of those moments: originally pressing period, exhausting and intenerated period, Al's consumption period,Al_2Ti's creation period, the main alloying and consolidation period and homogenization period.

i/Al-Al_2O_3系纳米级别的粉体在SPS上的烧结过程中，主要分为初始加压阶段、排气与软化阶段、Al消耗阶段、Al_2Ti生成阶段、主要合金反应与烧结阶段和均匀化阶段。

The low temperature sintering mechanism of SiC preforms and the effect of Graphite content on the density and dimension of the porous preforms were studied.

研究了SiC多孔陶瓷的低温氧化烧结机理和石墨添加量对SiC陶瓷骨架烧结密度和尺寸变化的影响。

Hydrothermal synthesis of tetragonal barium titanate from barium chloride and titanium tetrachloride;2. Sintered sample which has different amount of monoclinic and tetragonal phase at room temperature is obtained at different sintering temperature.

通过化学组成和相含量设计，采用湿混法制备了MgO和Y2O3共同稳定ZrO2粉末，在不同的温度下烧结，获得了室温下单斜相和四方相含量不同的烧结样品，用X射线峰宽化法测定并计算了粒子尺寸。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。