烧结

It has the capacity of producing 300 tonnes cast Alnico magnets with high performance annually.

公司拥有两个生产基地：年产600吨烧结NdFeB磁体、350吨粘结NdFeB磁体、50吨烧结SmCo磁体的平稀土永磁生产基地和年产300吨高性能Alnico磁体的深圳生产基地。

The properties of the material with finer andalusite particle size are superior to those of coarse particle size at lower temperature, but properties of material of fine and coarse particle size have little difference at higher temperature.

2对于不同粒度的原料，在烧成温度较低的情况下，粒度小的材料性能明显高于粒度大的材料，但在烧成温度较高的情况下，两者差别不大，说明原料粒度减小能降低制品的烧结温度，但在制品均完全烧结的情况下对材料性能影响不大。

Under contented the used intensity,the anorthite ceramic substrate which prepared with pyrophyllite at low-sintering temperature has small dielectric constant,good dielectric property which compared with common aluminum substrate,the anorthite ceramic substrate has light bulk density,which is advantage to reduc.

研究了用叶蜡石、碳酸钙与适量的氧化铝，在加入添加剂的条件下，用原位反应烧结法制备出低温烧结( 12 0 0℃)的新型钙长石质陶瓷基片材料。

The challenges of these material are screen printing and sintering process. Many long fine patterned lines should be printed on a large piece of glass and sustain a smooth, continuous and uniform line pattern; on the other hand, the sintering process is rapidly increasing sintering temperature to a peak in a short time, then cooling the glass substrate to low temperature under a short time shock.

汽车钢化玻璃除霜加热线，是采用在玻璃基板上印刷银浆，在玻璃的钢化热处理过程中完成银导体膜的烧结附着，由于烧结时间短(总时间250sec)和温度骤变条件相当苛刻，要求导电细线无脱落断线，在功率满足要求的情况下，与外蓄电池连接的电极的焊接及附着强度也有具体要求，另外耐候性及耐擦洗等后步要求也较苛刻。

This article introduces the microporous three-dimensional small-opening structure sintered by powder material, discusses the hydraulics characteristic of the narrow passage in the microporous material and the bubble chamber theory and expounds the general 1/3～1/7 empiric rule.

介绍了由粉末状材料烧结而成的微孔管三维孔隙结构，研究了PE烧结管三维孔隙之间的关系，并探讨了微孔管介质内细孔道的水力学特性和泡室理论，对通用的1／3～1／7经验规则进行了解释。

Machinability of P/M sintered steels with manganese sulfide and calcium fluoride additives is investigated and analyzed by experiments of sintering and cutting on milling machine.

通过烧结和在铣床上切削加工的实验，研究了添加硫化锰和氟化钙的烧结钢的加工性。

The fundamental formula of capillarity is employed on the Ru-based thick film strain resistors in the progress of sintering, and we get a mathematical model of this stage.

通过液态烧结阶段毛细作用的分析，建立相应数学模型，解释了导电相粒径、烧结时间、液气界面能以及玻璃粘度对应变电阻性能的影响。

It is found by X-ray diffraction that the solution of Sm2O3 and Gd2O3 in ceria for the samples sintered in the range of 1 400─1 550 ℃ is better, but for the sample sintered at 1600 ℃, a new phase is formed with the reduction of lattice constants.

X射线衍射分析发现：对1 4001 550 ℃烧结的样品，Sm2O3和Gd2O3固溶较好﹔但对1 600 ℃烧结的样品，有新相生成，同时晶格常数减小。

The main products of Trump Card are all steel double level vacuum extruder, compact vacuum extruder, non-vacuum extruder and all sorts of necessary accessories, such as JKY60/60-4.0, JKB50/45-3.0, JKR45/45-2.0, JKRJ45/45-2.0, GS80×60, SJJ300×50, ZQT650×200, ZQP24 and so on. The third generation of all steel double level vacuum extruder is widely applied to making various rigid plasticity and semirigid plasticity extrusion of load-bearing and non-load-bearing hollow bricks that its hole ratio is 25%-70%, from low-plastic materials like clunch, shale, coal gangue and coal powder.

乐山市泰辉机械制造有限公司制造的产品：JKY60/60—4.0，JKB50/45—3.0，JKR45/45—2.0，JKRJ45/45—2.0，GS80×60，SJJ300×50，ZQT650×200，ZQP24等系列全钢双级真空，紧凑型真空，非真空制砖机组及烧结制品生产线各种配套设备、全自动码坯系统等，广泛适用于粘土，页岩，煤矸石和粉煤灰等低塑性原料生产孔洞率25％—70％的各种承重、非承重空心砖坯的硬塑、半硬塑挤出成形，烧结、自动码坯系统等。

The results show that the coefficient of friction of Ti3SiC2 increases first and then decreases with the increase of sintering temperature.

采用环盘摩擦磨损试验机研究了烧结温度对反应烧结Ti3SiC2材料的干摩擦磨损性能的影响。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。