烧结

In this project, the new building wall material is made with manganese residue after electrolytic dioxide manganese.

本项目是利用电解二氧化锰产生的锰渣加入一定量的粘土等材料混合、搅拌、压制成型经烧结形成的新型墙体材料。

Polytetra-fluoro-ethylene thin membrane,pass through cut tie by poly-4 fluorous second fluidized resinde,after sinter cut but succeed,direct membrane transfusives membrane transfusive membrane mangler direct but succeed again,It has undeniable electrical equipment insulate behaviopural,non-ageing and extensive use temperature lint.

聚四氟乙烯薄膜，车削带由聚四氟乙烯悬浮树脂经模压，烧结后车削而成。定向膜将车削膜再经压延机定向而成，它具有优良的电器绝缘性能，不老化及广阔的使用温度范围。

Three Dimensional Simulation and Repair of Skull Maxilla and Dentition Based on CT Scanning and Laser Sintering Technologies.

基于CT扫描和激光烧结技术的上颌骨及牙列三维仿真与修复。

At the same time, the content of MgO of BF slag to increase 0.35 % reached 7.8-8.0%,the meltability temperature and viscosity of slag reduced, the fluidity of slag from 115mm impromed to 170mm, the iron loss from 7.09% decreased 5.15%, pig iron yield decreased 18t/d ,and comprehensive coke ratio declined 6.57kg/tp by indexes correction, effects of saving coke was significant ,and technical parameters of sinter and BF were optimized and improved,so that the content 7.8-8.0%of MgO of BF slag is suitable level.

高炉渣中MgO 含量提高0.35%达到7.8-8.0%，炉渣熔化性温度与粘度下降，炉渣流动性由115mm提高到170mmm，铁损由7.09%降低到5.15%，校正后产量小幅了下降18t/d，但综合焦比下降了6.57kg/tP，节焦效果显著，同时烧结与高炉的工艺参数得到优化与提升，炉渣MgO含量7.8-8.0%为较适宜水平。

And metallography analysis system was adopted to test the crystalline phase content.

用直接压痕法测量烧结样品的断裂韧性，运用金相图像分析系统进行晶相含量的测定，重点研究粉体粒度和晶相含量对长石瓷断裂韧性的影响。

The results showed the specimens by vacuum sintering had a typical Widmannstatten microstructure, which possessed coarser prior β-grains and secondary platelet α+β-phase, but the alloy had a more microporosity and a lower tensile strength and ductility. After HIP treatment, prior β-grains and secondary platelet α+β-phase became fine and uniform, and the alloy possessed a less microporosity and a higher tensile strength and ductility.

结果表明：真空烧结Ti-6Al-4V合金具有典型的魏氏体组织，其初始的β晶粒粗大，β晶粒内为次生片状α和薄β相片，空隙较多，合金的强度和塑性较低；合金经热等静压处理后，组织明显细化且均匀，空隙很少或几乎没有，从而强度和塑性都有所提高。

The effects of temperature on the density, hardness, strength, and microstructure of the composites were investigated.

研究了不同烧结温度对样品密度、Vickers硬度和弯曲强度的影响。

Effect of sintering conditions on the density, microstructure and magnetic properties were studied.

研究了烧结条件对磁体密度、微观结构和磁性能的影响。

A preparation method of nickel oxide-base cathode of fused carbonate fuel cell is to select alkali earth metal oxide, transition metal oxide and rare-earth metal oxide, mix with carbonyl nickel powder in the proportion of 0.01-15.00 mol%, add assistant and mix even into a slurry; after the slurry is formed into a biscuit by doctor-blade casting, sinter it into a multi-porous nickel plate; dissolve lithium nitrate and cobaltous nitrate with mole ratio of Li:Co-1:1 and citric acid or PVA in the distilled water to make a solution with Li of 0.00-0.5 mol/L; immerse the multi-porous nickel plate or nickel oxide plate in the solution, keep for 10-60 minutes under vacuum below 200 millibar, then dry in an oven at 75 degrees centigrade further transfer to a crucible electric furnace preheated 650 degrees centigrade for keeping the temp.

要約 熔融碳酸盐燃料电池氧化镍基阴极的制备方法属于燃料电池领域。选取碱土金属氧化物、过渡金属氧化物和稀土金属氧化物，按0.01－15.00mol％的比例与羰基镍粉混合，加入助剂，混合均匀成浆料；混合浆料流延成型为素坯后烧结为多孔金属镍板；将摩尔比为Li∶Co＝1∶1的硝酸锂和硝酸钴以及柠檬酸或聚乙烯醇溶于蒸馏水中，制成为0.005－0.5mol/L的溶液；将多孔金属镍板或氧化镍板浸入溶液中，在真空度低于200毫巴下保持10－60分钟；置于75℃的烘箱中烘干，转移至预热到650℃坩埚电炉中保温1－10小时；将此过程重复一次或多次即可。

Mineralizer such as TiO2,Cr2O3 and ZrO2 with proper amount, have a beneficial effect on the formation of magnesium aluminate spinel solid solution and the densification of samples, and decrease of porosity.

外加适量的TiO2、Cr2O3、ZrO2矿化剂能促进镁铝尖晶石烧结和晶粒生长，提高试样的体积密度和抗折强度，降低显气孔率。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。