烧焊

It owns complete sets of equipment ranging heat treatment, bimetallic roasting, alloy surfacing and testing.

公司拥有一系列完整的机加工，热处理，双金属焙烧，合金喷焊设备以及相应的完善检测设施。

In view of the superstandard total hydrocarbon problem found in the oil chromatographic analysis for No.

广东粤电流溪河发电有限责任公司1号主变压器通过油色谱分析发现总烃超标，吊罩检查找到引线绝缘击穿故障点，采用磷铜补焊的方法修复烧断引线，及时消除了重大安全隐患。

When the wainscots and the clapboards of the box structure are welded, wainscots can be born out and un-fusion will take place in the welder.

箱形截面构件壁板与隔板电渣焊时，易产生壁板烧穿和焊缝未熔合现象。

Experiments were conducted on a К900 rail flash welding machine by setting different welding currents at high voltage stages to determine the time at this stage.

采用К900钢轨焊机设置不同的高压阶段焊接电流进行试验，以测量在相同烧化量时的高压阶段时间。

The manufacture of copper core of automobile radiator includes coating tinned or bared copper cooling pipe; roasting assembled main core inside braze welding furnace at 230-280 deg.c for 30-60 sec; welding main sheet to cooling pipe via conventional process; and welding the copper lid opening for the water chamber with brazing agent without solder and welding filament.

一种铜质汽车散热器主芯的制造方法，其先将镀锡冷却管或裸铜冷却管外壁分别进行覆膜处理。将组装好的主芯主体置于铜钎焊炉内于230～280℃温度焙烧30～60秒。主片与冷却管间采用常规的方法焊合。还可以将组装好的主芯主体每排冷却管上摆放一根外表面涂有无钎料钎剂膜的锡焊丝，它们贴在冷却管与主片结合处。

This article describes briefly process procedure and characters of 5 sets rolling tack welders for longitudinal submerged arc welding pipe unit,and introduces common defects during tack welding operation,such as air pocket,slag,arc burn,offset and misalignment etc.

简述了直缝埋弧焊管机组中五组压辊式预焊机的工艺过程及特点，介绍了预焊作业中常见的气孔、夹渣、烧穿、错边、焊偏等缺陷。

Aiming at the engineering problem that K welding machine is used to weld PD3 60kg/m rail during welding production at present, the quality of the joint falls short of the standard of TB/T1632-91 because of the objection of grey-spots in the welding joint, this paper analyses the element which influence the welding joint quality in detail from the stability of flash of the accelerating step of the rail, finds out the relationship between the stability of flash-butt welding and the quality of rail joint, provides the measure for controlling the quality of rail welding and some gist for establishing perfect controlling system of welding joint quality

针对目前焊轨生产中采用K型焊机焊接PD3 60kg/m钢轨，接头灰斑缺陷多，性能难以达到部颁标准要求的工程问题，对材质、焊接电压、焊接工艺对接头质量的影响进行研究，并从钢轨焊接加速烧化阶段的闪光稳定性入手，详细分析了影响接头质量的因素，找出了钢轨闪光焊稳定性与质量的关系，提出了控制钢轨焊接质量的措施，为建立完善的焊接质量控制体系提供了依据。

For single-pass welds, the current should be sufficient for the desired penetration without burn-through.

对于单焊道焊接来说，电流必须足以使焊接达到所需深度，但不能烧穿。

The reasons of iron ions content overproof in grade Ⅱ desalting water system,such as variation water quality,contamination of regenerant , operation adjustment of pretreatment system and switching operation of bed were discussed.

对二级脱盐水系统中铁离子含量超标的原因，如来水水质发生波动、再生剂受到污染、预处理系统操作调整、床体运行切换等进行了论述。

You were hired to drum up new business, so go and do it.

公司雇你招徕新业务，你就做你的事好了。