烧

The microstructure of the sintered bone was observed by scanning electron microscope and mercury porosimeter. Results showed that the sintered bone possess the three dimensional space structure composed of macropores and micropores. The diameter of macropore was 50-400 μm and the diameter of micropore was about 1 μm. Results suggest the sintered bone of β-TCP remains the porous structure of natural cancellous bone which is benefit to growing of new bone.

结果显示β-磷酸三钙煅烧骨具有大孔结构和微孔结构相结合的三维空间结构，大孔孔径为50~400 μm，微孔孔径为1 μm左右，提示β-磷酸三钙煅烧骨保留了天然松质骨的多孔状结构，有利于新生骨组织的长入。

Iron grade is 35%～60%.Utilization of pyritic slag, the study on production of DR process metallization nodule with pyritic humidifying granding and forming was proposed.

利用硫酸烧渣，进行了煤基直接还原生产金属化团块的研究，提出了润磨造球-预热焙烧-磁选-冷固结成型的新工艺流程。

The rodlike nano barium ferrite was prepared in the conditions of pH=4,calcination temperature at 850℃ f...

通过对几个主要参数的摸索，得出制备棒状钡铁氧体的最佳工艺条件：pH值为4，煅烧温度为850℃，煅烧时间2h。

The influence of ratio of sagger and ceramic weight,the kiln car and ceramic,the leakage air volume in length in heating zone,the productivity of unit volume,outside sruface temperature of kiln crown,outside surface temperature of kiln wall,firing temperature,difference of firing in firing zone,length on firing zone,utlization factor on heat consumption was analyzed.

本文根据陶瓷隧道热工测定结果，分析了匣钵和瓷重比值、窑车和瓷重比值、漏风量、窑炉单位体积的产量、窑顶外表温度、窑体外表面温度、烧成温度、烧成带温差、加热带长度、窑道利用率对热量消耗的影响。

The morphology,crystal shape and size of nanopowder was characterized and analyzed by XRD,SEM technologies,the yield of preparation was considered,and the best technic parameters was obtained:titanium tetrachloride∶n-octanol is 1∶4,the temperature of ammonium carbonate satura...

通过XRD、SEM对纳米粉体的形貌、晶型、粒径进行了表征对比，并结合二氧化钛粉体制备的产率，确定了最佳工艺参数：四氯化钛∶正辛醇=1∶4，碳酸铵饱和溶液温度为50℃，真空干燥温度为110℃，焙烧温度350℃，焙烧时间3 h。

In this paper, two assemblies of special test equipments have been designed and fabricated by authors in our laboratory: namely Catalyst Molding Process Analyzer and Catalyst Mechanical Process Tester. These new skills are developed for the dynamic studies on whole mold forming process and crushing process of Fe-Cr WGHS catalyst pellet. Based on the orthogonal experimental design, the effects of some factors during the forming process of solid catalyst, such as predensification proportion, calcination time, calcination temperature and content of graphite on the mechanical strength of catalyst pellets are systematically examined, and the molding conditions have been optimized. Based on the experimental data, the relationship between catalyst density and forming pressure are educed, and the physical significances of some related parameters are described. The parameter of macro scopic elastic moduls has been suggested to character the mechanical properties of molding catalyst. The effects of molding pressure on mechanical properties of catalyst pellets are discussed, and results show that there exists a optimal molding pressure for the ideal mechanical properties: when over-high or over-low pressure is applied, the specific surface area and side crushing strength of catalyst pellets will decreased. The "rebound effect" will be undermined by the unsuitable pressure maintain process, resulting in the apparent decrease of mechanical strength of catalyst pellets.

本研究通过自行设计制造的催化剂模压成型过程分析仪（Catalyst Molding Process Analyzer， CMPA）和催化剂力学性质测试仪（Catalyst Mechanical Properties Tester， CMPT），以Fe-Cr系高温变换催化剂片剂为研究对象，对成型过程和受压破碎过程提供了全过程动态研究的新手段；本研究利用正交实验设计方法考察了固体催化剂成型过程中诸因素（包含预密致比例、煅烧时间、煅烧温度和石墨含量等）对催化剂成型体强度的影响，并对成型条件进行了优化；根据实验结果，关联确定了固体催化剂成型过程中的密度－压力关系式，并对方程中诸因子的物理意义进行了描述；提出了一种利用宏观弹性模量来表征成型催化剂的力学性质的方法；研究讨论了成型压力对催化剂成型体强度性质的影响，结果表明：对于催化剂成型体的强度和比表面性质，成型压力存在着一个最佳值，过高的成型压力会导致比表面积和侧压强度的降低；不适当的成型压力的维持时间会破坏&压力回弹&作用，造成催化剂成型体的机械强度明显降低。

His hands were burnt and dirty and his overalls were singed and smoking.

他的双手被烧焦了，非常肮脏，他的外衣也被烧焦了，冒着烟。

It is found that the higher the calcination temperature of MgCO3,the smaller the specific surface area of MgO is,so is the initial reaction rate of sulphation of MgO.

实验表明，菱镁矿(主要成分MgCO3)的煅烧温度越高，其煅烧产物MgO的比表面积越小，因而MgO硫酸盐化的初始反应速率越低。

The results show that at 1500℃ a clinker was obtained in which the content of tricalcium silicate is 74.52%.

在工业回转窑正常煅烧温度下烧成了C_3S含量达70.71%的熟料。

The fields of application of calcined FGD gypsum were gypsum wallboard,building plasters,self-leveling floor plaster,etc;The fields of application of uncalcined FGD-gypsum were cement, agricultural soil amendment, etc.

经煅烧的脱硫石膏的应用领域主要有：石膏墙板、建筑灰泥、自流平地板灰泥等；未经煅烧的脱硫石膏的应用领域主要有：水泥、农业土壤改良等。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新