烟道
- 与 烟道 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Moreover, high removal efficiecvy was observed for large particles if the adhesion force between the particles and bed materials overcame the rebounce effect.
因此当烟道气中同时存在甲苯气体时,去除效率以4μm Al2O3最高,其次才为80 nm及20 nm Al2O3。
-
The gas burning lime upright stove is improved at Jigang. The cylinder form was changed as rectangular plus arcuate forms, the structure of lime discharge machine was redesigned, the air and gas heat exchangers are connected in series in dedusting flue. The rate of raw and over burning of lime is less than 7%, the breakages of tooth and shafts on lime discharge machine are decreased and gas is saved.
济钢对气烧石灰窑进行改进,将圆柱型窑形改为矩形+弓形,并重新设计了出灰机结构,在除尘烟道上串联增设了空气,煤气换热器,使石灰的生,过烧率低于7%,减少了出灰机的断齿,断轴现象,而且节约了煤气。
-
The flue gas temperature of direct-fired machine is too high to save energy.
直燃机排烟温度过高,不利于节能,在烟道上加设余热回收装置。
-
Advanced roller-bottom style heating furnace technique was adopted in 1880mm hot mill stand of Benxi Iron and Steel Co.
本钢1880mm 热连轧机组采用了先进的辊底式加热炉技术,其烟道工作衬设计采用1260℃绝热涂抹浇注料,使用3~4个月耐材出现较严重的剥落现象。
-
In commercial or industrial jobs, they build concrete forms, scaffolding, bridges, trestles, tunnels, shelters, towers and other structures.
在加拿大工业建筑,或加拿大商业建筑工作中,做混凝土预制板模具,建脚手架,楼梯梁,栈桥,烟道,棚屋和塔楼等。
-
These factors have seriously influenced the security and economical operation of the unit. This paper firstly summarizes the research background and the general situation of resarch about the overheating problem of boiler's high-temperature surface ,introduces the aspects and research findings in this field such as flux deviation、thermal deviation、flue gas velocity deviation at the exit of furnace and tee bends,et al.Then analyses the reason why high-temperature surfaces are overheated from such aspects as design、manufacture、operation, et al and points out one of the main factors that cause the overheating of reheaters is the flue gas velocity deviation caused by the remaining turning at the exit of furnace.
本文首先综合论述了课题的研究背景和目前电站锅炉高温受热面超温问题的研究概况,介绍了国内外流量偏差、热偏差、炉膛出口残余旋转、&三通&等研究方向和研究成果,然后从锅炉的设计、制造、运行等方面分析了高温再热器超温的原因,指出水平烟道内气流的残余旋转是造成再热器超温的主要原因之一。
-
The furnace is possessed of multi-function complex lining, adjustable sub-high speed burner, burner adopting symmetric arrange, naturally draining away fume from fume offtakes, pressing soft sealing with rail, combining control by hand or automatic way.
该炉型属于台车式热处理炉,具有多功能复合炉衬和可调型亚高速烧嘴,烧嘴采用&一&字形左右对称布置,烟道为低位多点分布自然排烟,弹性接触轨道压紧软密封,自动与手动控制方式相结合。
-
If the old house emissions flue is not a good situation, then the best way forward is for the yin and Taiwan into the workplace, the exhaust pipe directly from the overcast outdoor Taiwan received the stove and range hood is in Taiwan Yin , so the fumes will be wiped out to cook, and kitchen cabinets can be put down more, the design can also be more subtle and reasonable.
如果老房子烟道的排放情况不是很好,那么最佳的方法就是把阴台变成工作间,把排风管直接从阴台接到室外,把灶台及抽油烟机都安排在阴台上,这样做饭的油烟就会一扫而光,而厨房也可以放下更多的柜子,设计上也可以更加巧妙合理。
-
As the radiation heating surface,the membrane wall is installed in the down pass of the CDQ waste-heat boiler .
分析了作为辐射蒸发受热面的膜式水冷壁布置于干熄焦余热锅炉的竖直烟道内,在低热负荷下水循环安全问题。
-
Today the solder joint is widely adopted, as evidenced by the majority of cities and states that have written codes to include copper tube and solder joints as desirable for general plumbing, water lines, vent, stack, waste and drain lines, as well as other uses in industry.
如今,焊料连接已经被广泛采用,证据就是美国大多数城市和州的正式规程中都将铜管道和焊料连接作为一般管件、水管线、通风、烟道、废水和排水管道以及其他工业用途的理想连接方式。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。