点过程

The relationship between the apparent viscosity and temperature can be expressed by Arrhenius Equation. But there is a flex point during heating, and the viscous flow activation energy at the low temperature is greater than that at the high temperature.

液化残渣的黏度－温度关系符合Arrhenius关系式，但在升温过程中出现了拐点，低温段的黏流活化能比高温段的要大。

Just because the difference quality of the two has determined the necessity studying too;OP has flex point which can be used to judge AT in the course of sport ,and research proves that the means is more accurate;Research proves that no positive pertinency is between OP and HR,but the author believe it only accounts for lack of the quizzees;The better the enginery of human is,the higher the positive pertinency among VO2、OP and HR is.

也正因为二者的差异性决定了研究的必要性；氧脉搏在运动过程中存在拐点，可以判断无氧阈。

According to the migration law of each sintering zone, the temperature at the flexions can be obtained, which represents that the forefront of each sintering zone arrive at the sintering grate.

结合烧结过程各带的迁移情况，计算得出拐点所对应的各带前沿到达料层底部的温度。

The approach primarily adopts patch-based texture synthesis flow, synthesizing progressively-variant textures to reflect the diversification trend of vector fields.

在纹理合成过程中利用向量场作为指导，生成反映向量场大小和方向变化的合成结果·采用块纹理合成的流程，在对向量场合成块均匀划分的基础上，通过进一步的自适应分割，将向量场划分成为不同大小和不同形状的最终合成块，使之与向量场的变化趋势相吻合·对向量变化过于剧烈的区域，则采用点合成的方式进行纹理合成，以保证合成效果的平滑·实验表明，文中的方法可以实现快速而高质量的向量场可视化

It is necessity to take an impact test for FOPS in laboratory in order to install falling object protective structures at engineering vehicle and check its dependability.

为了对工程车辆的落物保护装置进行可靠性试验提供理论依据，采用冲击动力学的塑性波两侧的动量平衡理论对工程车辆FOPS受冲击时落锤的动态响应进行了研究，建立了锤头变形的基本方程，绘制了方程相应曲线；建立了锤头在冲击过程中任一瞬时变形长度和非变形长度的数学模型，找到了工程应变和冲击速度之间的曲线对于塑性大变形的突变点及影响落锤变形的各个因素和控制变形的依据。

The main research works and innovations of this paper are as following: Firstly, the key problems for long term monitoring of long span cabled staged bridge are put forward.

本文的主要研究成果和创新点如下： 1、提出了大型斜拉桥长期健康监测过程中的关键技术难题。

The limitations of describing how the nugget growing up in view of single-sensor information source is analyzed in the paper.An idea of using multi-sensor information fusion for spot welding quality control is presented for the first time.

本文分析了基于单一传感器信息资源来描述焊点熔核形成过程存在的局限性，首次提出了采用多传感器信息融合控制点焊质量的思想。

In order to study the change of the thickness of gas hydrate stable zone and its effect on environment, 35 spots from four key areas in the southern South China Sea were selected to calculate it based on relative equation and program.

为了研究南海南部天然气水合物稳定带厚度在这个过程中的变化情况及其对环境的影响，我们利用相关的计算公式，并编制了计算稳定带厚度的程序，在南海南部的南沙海槽、曾母盆地、巴拉望盆地和苏禄海等四个重点海域选取了35个点进行末次盛冰期及目前稳定带厚度的计算。

The mold structure and working principle were introduced in detail, mainly stated in detail design of angle pin and pin gate .

通过对照相机前盖的使用要求以及工艺性分析，介绍了基于Pro/E注射模设计基本流程，并详细介绍了该注射模的结构和过程，重点阐述了斜销及点浇口设计要点。

On the basis of equivalent planar pitch,the tooth profile of the equivalent gear was gotten through simulation when the pitch curve of the gear shaper rolled on the equivalent planar pitch curve.

以平面当量节曲线为基础，通过确定插齿刀的节圆沿平面当量节曲线做纯滚动时插齿刀上各点的运动轨迹，模拟了插齿加工包络出当量齿轮的齿形过程，将非圆锥齿轮的设计转化为平面齿轮的设计，简化了非圆锥齿轮的设计。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。