点过程

This paper raises an objection to the method of gettinS special points on the intersection curve by using analytic geometry and graphic method.

而在求解这一系列公共点的过程中，较准确和方便地求出控制相贯线形状和位置的特殊点的问题，尤为突出。

To data management, this paper mostly discusses data manipulation and input of trig point result and bench mark result.

数据处理工作部分，主要讲述全省三角点成果和水准点成果的数据处理及入库过程。

Other orders bench mark of Shandong province need to be adjusted and then could be inputted into database by rules.

本文第二章和第三章就分别介绍了三、四等三角点成果和山东省水准点成果平差处理的方法和过程。

Difficulties: quasi-static process and reversible process; Calculation on heat and work in reversible process

难 点：准平衡过程和可逆过程的定义，可逆过程的热量和功量计算。

Focus: equilibrium state, quasi-static process and reversible process, state properties and path variable, etc.

重 点：平衡状态、准平衡过程、可逆过程、状态量与过程量等。

This paper analyzes the principle of the LP-LFC process,presents the physical and mathematical models of mould filling of the new process. The patterns including window-plate, ladders cluster, electromotor frame and exhausting manifolds are poured using LP-LFC process with AZ91D alloy, and the mould filling course is tracked with electrode touch point method. Based on above tests and experiments,the casting defects including short runs, cold laps, trapped gas,metal penetration, and so on, were investigated. The appearance characteristics,birth causes and influence factors of above defects are discussed in the article,diagrammatize modes of the defects forming is also given, and the measures of reducing or avoiding defects are put forward.

本论文分析了低压消失模铸造技术的工艺原理，建立了低压消失模铸造过程中金属液充型的物理和数学模型；在各种工艺条件下浇注了薄板窗体、阶梯模样簇、电机外壳和发动机排气管四个典型的模样和产品，用电极触点法记录了镁合金低压消失模铸造的充型过程；试验研究了镁合金低压消失模铸造中出现的浇不足、冷隔、气孔、粘砂等典型缺陷，分析了这些缺陷的形貌特征、形成原因及影响因素，给出了缺陷形成过程的图解模型，提出了减少和消除缺陷的工艺措施。

3The heat transfer in the charging and discharging process are unsteady, and the heat transfer capability of the system will change against time, and the charging rate and discharging rate decreases gradually with time, as should be noticed in the design.

蓄冷和放冷过程都是非稳态传热过程，整个过程中系统的传热能力是不断变化的，蓄冷率和释冷率都是逐渐降低的，在蓄冷设计时应该注意到这点。

During the moisture adsorption process from oven-dry state to the equilibrium state in 20℃, 60％RH environment, the activation enthalpy of adsorbed water during reorientation increases linearly with adsorption time.

从绝干状态→20℃，60％RH平衡态的水分吸着过程中，吸着水分子在回转取向过程中的活化焓随着吸湿时间呈线性增加，这说明一个吸着水分子与周围木材吸着点之间的氢键结合数的平均值随着吸湿过程的进行逐渐增多，直至达到平衡状态。

The method firstly determined the pinch point and the minimum utility targets of the batch processes by the water cascade analysis technology, then synthesized the water network by using the diagram and rules, and then determined the number and volume of storage tanks for batch processes with storage tanks,and lastly described the synthesized optimum water network by the time-water network diagram.The influence of the water network by the flowrate demand of a water-using process was also discussed.

它首先通过水级联分析技术确定间歇过程用水网络的夹点及最小公用工程，然后利用时间-纯度图和设计规则来合成用水网络，对有储罐的情况，确定了储罐的数量与容量，最后利用时间-水网络图描述了所合成的最优间歇过程用水网络，并探讨了用水过程流量对网络的影响。

The results show that both of the "anaerobic" wastewater treatment and the sludge anaerobic digestion make the organic compounds in sludge so complicated that the organic compounds decomposition and release temperature becomes higher during pyrolyzing, and the "aerobic+anaerobic" process makes the organic compounds in sludge more complicated than the "anaerobic +aerobic" process. There is no influence on the combustion process and the burnout point, but can make the combustion temperature of sludge higher.

结果表明，污水处理工艺的&好氧＋厌氧&、&厌氧＋好氧&过程以及污泥的厌氧消化均使污泥中的有机物结构复杂，导致污泥热解时有机物的分解和析出温度升高，且&好氧＋厌氧&过程使污泥中有机物结构更复杂；而对污泥的燃烧过程和燃尽点无影响，但使着火温度升高。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了