点过程

The carbonization process meets the needs of the model of condensation reaction .

结果表明，在反应初期为化学反应动力学过程点后才过渡到扩散动力学过程，碳化反应符合缩核反应模型。

According to contraction theory, this algorithm is based on gradient descent method, which adopts linear average as performance evaluation of value function. So the iterative process of value function becomes a convergent process to a fixed value.

该算法基于梯度下降法，根据压缩映射原理，通过采用线性平均法作为值函数估计的性能衡量标准，把值函数估计的迭代过程转化为一个收敛于不动点的过程。

Analyzing the calculating process of belt conveyor with high angle theoretically, starting from its theoretic calculate the cross sectional area of materials and peripheral force, shaft power of drum, power of motor, using point by point method to get the resultant strain of every drum and torsion of driving drum, calculating the maximum strain and the maximum reverse stopping torque, to give the support on theory for using belt conveyor with super-long distance, high angle under the coal mine.

本文针对长运距、大倾角、高强度带式输送机设计过程中存在的问题，从四个方面对大倾角带式输送机进行分析研究：从理论上解析大倾角带式输送机的计算过程，从大倾角带式输送机的理论入手，详细计算物料的横截面面积、圆周力、滚筒轴功率和电机功率，利用逐点计算法计算各个滚筒的合张力以及传动滚筒的扭距，计算出胶带的最大张力和最大逆止力矩，给长运距、大倾角皮带机在煤矿井下的使用给予理论上的支持。

At present, in the production craft of construction ceramics, generally has used the more advanced tunnel kiln to fire the craft, carries on in the process in the use tunnel kiln which fires, fixed time and fixed point completes goes against the vehicle work is the guarantee fires one of quality important methods, this article carries on the discussion on the entire tunnel crown vehicle craft PLC control.

引言目前建筑陶瓷行业普遍采用的是隧道窑烧成工艺，在使用隧道窑进行陶瓷烧制的过程中，除了严格控制各被控点的温度和压力等物理参数外，精确、准时地完成顶车、回车等循环过程，也是保证烧成质量的必要环节，随着计算机技术的发展，特别是可编程逻辑控制器技术的广泛应

The dielectric barrier discharge process in the NOx O2 mixture gas was simulated, and the γ-Al2O3 spherules in the gas gap were found to increase the space electric field.

模拟了NOx O2混合气体中的介质阻挡放电过程，发现γ-Al2O3小球使气隙中的空间电场在小球间的接触点得到显著增强，从而增强气体放电过程。

The pinch point technology and the mathematics programming method are the main means in the process system energy integration and optimization. But both of them are with the first law of thermodynamics for foundation, they only make sure the quantity relation in energy conversion process and neglect the difference of quality of energy.

夹点技术和数学规划法是过程系统能量综合优化的主要手段，但它们均以热力学第一定律为基础，仅仅确定了能量转换过程中的数量关系，而忽略了能量品质的区别。

On the basis of analyzing the thermodynamic properties and cycle performance of pure refrigerants, the paper optimizes their concentration while screening NARMs used in wide variable-temperature heat source. The practical applications of NARMs, such as R22/R123, R123/R125 etc., are studied in geothermal heat pump, seawater heat pump, air dehumidification system and dual-evaporator domestic refrigerator. The results show that the NARMs can match the limitation of a pinch point at the air-side exit of heat exchanger, reduce the unreasonable heat transfer temperature difference, and improve the COP of system. The above conclusion is proved by measuring the cycle performance of R12, MP39 and R11/R22 in a two-evaporator experimental system.

其次，本文在工质热物性和变工况循环性能分析基础上，筛选和优化了适应外部大变温热源约束条件的非共沸混合工质及其浓度配比；讨论了相变温差较大的非共沸混合工质（如R22/R123、R123/R125等）在地热源供热热泵、海水源供热热泵、双门冰箱和热泵空气除湿的应用，计算分析表明制冷与热泵系统采用相变温差较大的非共沸混合工质有利于弱化传热过程的&窄点&的约束，减小传热过程中的不合理温差，提高系统COP值；通过建立双蒸发温度循环系统试验装置，对R12、R22/R11和R22/R152a/R124循环性能进行实验研究，结果与理论分析一致。

After the research of anodic oxidation slag, we got the composition of the suspension electrolyte of zinc sulphate solution. 2 The results of electrode kinetic of anodic oxidation showed that the electron transfer during the process of electrochemical oxidation was 1, and the electrochemical mechanism was: ZnS=Zn~(2+)+S~-+e Zn~(2+)+2S~-=ZnS + S~0 3 The flow sheet which can produce zinc according to suspension electrolysis principle in industry was put forward. 4 Elemental sulfur in oxidizing slag was recovered by distillation.

本文的创新点是： 1提出了以硫酸锌溶液为基础的悬浮电解液体系；通过对阳极氧化渣进行系统的分析研究，得出了硫化锌矿物的悬浮电解的电解液组成； 2通过阳极氧化电极过程动力学分析得到，电化学氧化过程中电子转移数为1，电化学机理为： ZnS=Zn~(2+)+S~-+e Zn~(2+)+2S~-=ZnS+S~0 3提出了工业上利用悬浮电解原理生产金属锌的工艺流程； 4对氧化渣中的元素硫采用蒸馏法原理进行回收。

A method of computing and visualizing the combustion process in a DI gasoline engine is presented, taking a complex shape DI combustion chamber as a case, basing on a three-dimensional staggered grid, using a zero-dimensional combustion model with sequential multi-point combustion in this paper.

本文研究了缸内直喷式汽油机燃烧过程的计算机模拟计算与燃烧过程可视化方法。论文以一个复杂形状的直喷式燃烧室为例，基于三维交错网格，应用零维燃烧模型，按照油束形状以多点连续燃烧的形式计算研究了该方法。

The process of convergence is to use the information of the time dimension. For the low signal noise ratio problem, detection of target in a single frame image is difficult, and the method is excellent.

考虑把点目标跟踪预测的过程视为是函数近似的过程，这是一个病态问题，可以用正则化理论来解决。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。