点角

The property of the point of inner corner reflects the material single tensile property, the main function of the point is σ〓 and ε〓.

接管角焊缝内拐角点的特性基本体现了材料的单向拉伸特性，该点起主要作用的是σ〓和ε〓。

Methods: The following measurements were obtained using a slidin g gauge and ophthalmostatometry on children 5～17 years of age: The anthropometr y of interpupillary distance, inter outer canthal distance, inter oto bsion superius distance, length of nose, inter alare distance , frontal angle, distance between otobsion superius and outer canthus, and exophthalmus.

对厦门市5～17岁儿童少年2600人以电子数显游标卡尺、弯脚规和Hertel眼球突出计进行了瞳孔距离、眶距、耳根上点眶距、耳根上点间宽、眼球突出度、鼻高、鼻宽和鼻基根角的活体测量。

The four edges of each isosceles trapezoid are detected and the vanishing point of the direction of parallel edges and four corner points are worked out.

给定k(k≥6)幅包含等腰梯形的图像，分别检测梯形的 4条边，计算梯形平行边方向上的消影点和 4个角点。

And there is an approximate linear relationship between the momentum of the automatic mechanism and the length of the gas tube.

如β=〓与β=〓相比较（β角单位为弧度，其定义详见正文），前者与后者对应的气室最大压力之比可达65%，而对应的自动机动能之比可达60%；导气管内径对气室内气体压力冲量和自动机动能的影响存在极值点，且该极值点随导气孔的增大而有规律的增大；导气管长度对气室最大压力、压力冲量和自动机动能的影响呈单调递减规律，且自动机动量与管道长度之间近似符合一直线关系。

Finally, based on the relative observation data of LS and CCD, the position of objects in local coordinate system can be obtained.

在近景目标三维测量系统中，是根据GPS定位平台的姿态角，通过GPS平台、激光扫描仪及CCD相机之间的固定位置关系，得到CCD相机、激光扫描仪的姿态参数，依据扫描仪和CCD相机对地物点的观测，解算出地物点在当地坐标系下的坐标。

In the experiment the pre-processings, such as image filtering and Harris operator corner detector, etc. were used to get feature points quickly and realize the mapping transformation of camera parameters. The error estimate function was established to compare the proposed method with Tsai calibration algorithm.

实验过程中，利用图像降噪、改进的Harris算子角点提取等预处理过程快速提取特征点，实现摄像机参数标定的映射变换；建立了误差评价函数评价本文方法与Tsai标定算法。

In the experiment the preprocessings, such as image filtering and Harris operator corner detector, etc., were used to get feature points quickly and realize the mapping transformation of camera parameters. The error estimate function was established to compare the proposed method with Tsai calibration algorithm.

实验过程中，利用图像降噪、改进的Harris算子角点提取等预处理过程快速提取特征点，实现摄像机参数标定的映射变换；建立了误差评价函数评价本文方法与Tsai标定算法。

There may be more extra-landm ark noise associated with the measurement of angle NAPg than with the other thre e angles.Since change in SNA is affected by Nasion horizontal displacement,its r epresentation of Point A displacement was questionable.

除了NAPg，其它3个角度的变化基本能反映出颌骨及牙齿在矢状方向的位置改变，但SNA角的变化在一定程度上同时受N点水平向位移的影响，使其反映A点水平向位置改变的可靠性受到影响。

Numerous impermeable underground structures exist in urban seepage field. Since the corner of the structure is singular point and the dimension of the structure is negligibly small compared with the whole urban seepage field, it is difficult to model seepage field in urban area with existing methods.

城区渗流场中地下阻水结构物众多，由于结构物角点为奇异点，而且结构物的尺寸跟整个渗流场的尺寸相比起来非常小，这导致现有的计算方法难以对城区渗流场进行模拟分析。

While the experimental side force distribution over a slender body with a blunt ogive nose is basically consistent with the curve of the analogy predicted, and the characteristic points and half cycle of the experimental curve are basically constant with the roll angle changing 360°. But the local maximums in the curve are not the results as the analogy predicted, which is an important flow feature of 3-D slender body than that of 2-D cylinder.

而钝头拱形细长体在大迎角下的截面侧向力分布与脉冲起动横流比拟方法预测的侧向力曲线的形状是基本相同的，而且随着滚转角旋转360°，截面侧向力分布曲线的特征点和半周期基本保持不变，即它们都基本上不受滚转角变化的影响；但是截面侧向力分布曲线极值点形成的原因却是不同的，这是细长体绕流区别于二维圆柱绕流的一个重要特性。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。