滚

In the direction perpendicular to the rolling plane convex curve was continuous basic cylindrical or conical roller to prevent roller and raceway contact points to the stress concentration.

在垂直于滚动方向的平面内呈连续的微凸曲线的基本圆柱形或圆锥形的滚道，以防止在滚子与滚道接触处产生应力集中。

In order to solve the problems of rotary kiln in the overall rolling ring such as casting, transportation, installation and demolishment. Try to design rolling ring in split form.

针对目前回转窑整体式滚圈在铸造、运输、安装及拆卸等过程中存在的难度，提出设计剖分式滚圈的设想，以解决整体式滚圈存在的问题。

Roll a bucket to electroplate generally, roll a bucket inside of the work piece

一般的滚桶电镀，滚桶内的工件是随着滚桶的转动而翻动。

Variety including gulley ball bearing, cylindrical roller bearing, spherical surface roller bearings, circular cone roller bearings, angle contact ball bearing, needle bearing and other many kinds of types.

品种包括深沟球轴承、圆柱滚子轴承、球面滚子轴承、圆锥滚子轴承、角接触球轴承、滚针轴承及其它多种类型。

My factory product mainly includes the British system circular cone roller bearings, the gulley ball bearing, the accent heart roller bearings, the cylindrical roller bearing and so on, simultaneously my factory may make each kind of non- standard bearing according to the customer request.

我厂产品主要包括英制圆锥滚子轴承、深沟球轴承、调心滚子轴承、圆柱滚子轴承等，同时我厂可根据客户要求制造各类非标准轴承。

We all know that roller, block between hobber and hobber for the imprint, but the artificial division between rolling roller, block roller and embossing roll is a compact, linear three-roll and is consistent, so when the pressure is too large, due to the printing plate is compressed with the roller between a certain amount of sliding friction, thereby allowing the printing plate abrasive.

不小家都懂得，网纹辊、印版滚与不抬印滚之间虽说是滚不抬，但是网纹辊、印版辊与不抬印辊是有不抬缩的，而不一辊的线速量又是分歧的，所以当不弛力过不小时，由于印版被不抬缩会与网纹辊之间爆发必定的滑动摩擦，从而使印版爆发磨损。

The third type of formula can only meet the occipital hobber didn't go to an offset printing press for offset press since hobber in regulating rubber roller roller and nano-imprint lithography, clearance between the plate cylinder and penetrated the rubber roller is no need for regulation, walk for offset printing presses in the hobber business card printing and membership card making paper thickness greater than 0.10mm the above with a formula for the calculation and adjustment.

第三栽筹算公式只能满意不行滚枕的胶印机，而行滚枕的胶印机由于在调度橡皮滚筒与压印滚筒之间的间隙之后，印版滚筒与橡皮滚筒之间的间隙必须举行调度，那行滚枕的胶印机在制卡和会员卡制作纸张的厚度大于0.10mm以上不离用第二栽公式举行筹算与调度即可。

When using the die-cutting tool, be sure to use industry gently rolling shouder strickle blankets up drop every day in order to maintain an adequate amount of lubricant die-cutting knife at the end of shouder hobber and the stone the roller surface clean, and in both form a thin film to improve die-cutting knife at the end of shouder hobber and rolls of anvil wear resistance.

搁置模切刀时，一不退给对峙搁置厂家供答的滚肩刮拭毛毡，每天进取滴适度润滑油，以保留模切刀滚肩与底砧辊暗不天的肮脏，且在两者间变成一层薄薄的油膜，恶化模切刀滚肩与底砧辊暗不天的耐磨损性能。

Part of the normal roller, the fault is not resolved, check for roller pressure, which can use FUSE (electrical purposes 20, fusealways) and qianyanzhou hobber in rolling direction, not to mention the occipital clearance to unload their plates and blankets, the slot for the Department in the roller snthase pad, if rolling pillow gap over specification number, the adjustment of the diaphragmless, the pillow are met at both ends of the clearance requirements, you can troubleshoot.

墨辊局部变态了，障碍仍未处置，再查抄滚筒之间的不张力，可用电工用不焊接丝（20号保障丝）和千分卡轧测滚枕间隙，必须卸下印版和橡皮布，在滚筒的不满档处分不抬轧测，若滚枕间隙超功表明书规矩的数值，则调动调不抬器，使滚枕两头间隙都相符表明书上的请求，即可摈斥障碍。

Based on these researches, the hollow planetary roller design method of using the hollowness as main parameter is proposed.

进而，结合对行星滚子的弯曲疲劳的讨论，提出了以滚子空心度为主参数的中空行星滚子设计方法。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。