滑转

In this paper the author has discussed two foundamental methods--control of tractive force and control of slippage ratio which in testing the wheel or crawler tractor.

本文叙述了对轮子或履带试验的两种基本方法——控制牵引力法和控制滑转率法。

If the slope is 16°, load is 100N, and slip ratio increases from 0 to 0.6, the relative errors of predicting normal force, drawbar pull and driving torque between calculation values and experimental data are less than 10%. The model can predict wheel-terrain interaction mechanics effectively for a rover while climbing up slopes.

在斜坡角度为16°，载荷为100N，当滑转率从0增加到0.6时，将模型的车轮斜坡法向载荷、挂钩牵引力和驱动力矩的计算值与实验数据相对比，结果相对误差不超过10%，因而该爬坡模型可以有效地用于月球车轮地相互作用的力学计算。

It is proved that the control logic using PI controller based on driving wheel slip rate work efficiently in simulation.

基于驱动轮滑转率控制的PI控制方法经过仿真验证是有效的。

The ECU developed with the in-the-loop simulation technology is fitted on a light duty vehicle and tested,the result shows that overspin of the d...

将利用硬件在环仿真技术开发的ECU安装在某轻型车辆上进行试验，结果表明，该车驱动轮的过度滑转情况得到抑制；该系统可较好地模拟车辆系统和试验环境，并可替代部分实车试验。

Results show that, when the wheel slip ratio is in the range of 0 to 80%, both Drag-bar Pull and Traction Efficiency increase with the number of simulant regolith press. When the simulant regolith is pressed two times, the DP and TE increase 38.9% and 69.9% respectively.

试验结果表明：当滑转率在0~80%时，挂钩牵引力和效率系数呈现增加趋势，压实2次和4次的模拟月壤分别比自然状态时最大挂钩牵引力提高了38.9%和66.7%，最大效率系数提高了69.9%和171.6%。

A wheeled vehicle to be fitted with common rubber-tire does not adapt to the desert area because of wheel slip sinkage.

装用普通充气弹性轮胎的轮式车辆在沙地上行驶时，由于车轮滑转下陷，使车辆难以通过。

Moreover,the two wheels of the exactly similar diametercan only turn at the same speed without slip on the straight road.

Moreover 上，完全相似直径的这二个轮子才能在直的道路上以相同的速度没有滑转。

Hover telemark end in p.p.

盘旋滑转步，结束在侧行位置 SQQ

The combined control strategy of the engine gun control, the slip ratio control and the power control is put forward.(6)Based on the structure and parameters matching of a cold milling machine, a kind of adaptive controller which can be used on the cold milling machine is developed.

在研究控制算法的基础上，对冷铣刨机功率自适应控制主要模块的控制策略进行了研究，并给出了软件设计的流程图，提出了冷铣刨机作业过程中发动机油门开度、滑转率及功率自适应三者的联合控制策略。6。

And a control logic using wheel speed as primary threshold and acceleration as secondary threshold was designed.

选择以驱动轮相对滑转率和加速度为控制门限设计了控制逻辑。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。