滑移的
- 与 滑移的 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Occurs when the semi-finished, warping, especially the post-mounted corrugrted semi-finished products, immediately after the closing of embossing plate, on the paper--and there is no uniform die to tilt paper with the sponge rubber or contact, so easily make embossing plate produced by 印张 bliding, die-cutting production phenomenon.
当半成品出现卷曲、起翘情况时,特别是经过裱贴以后的瓦楞纸板半成品,放在压印平板上合压时,纸面与模切版没有均匀接触,使翘起的纸面先与版面上的橡胶条或海绵接触,这样容易使压印平板上的半成品印张产生滑移现象,造成产品模切不准。
-
The results show that the friction coefficient and slip rate can derived from the test, which benefits the understanding of ABS operation principle and development of relatebed control technology.
结果表明,采用实际测试分析,可以得到制动过程中摩擦系数和滑移率的具体值,它有助于对ABS实际工作情况的了解和相关控制技术的研究。
-
When the soil behind and/or beneath such a wall liquefies, the pressure it exerts on the wall can increase greatly - enough to cause the wall to slide and/or tilt toward the water.
如果这些码头岸墙基底、或者背面的土壤发生液化,施加于岸墙上的压力将会骤然发生大幅的增加,甚至增大到足以使这些岸墙发生滑移或者向水面侧倾的程度。
-
The two definitions of dilatancy in slip line theory are clarified, and the generalized Mises yield criterion matching Mohr-Coulomb yield criterion in plane strain condition is put forward where the effect of dilatancy can be considered.
阐明了滑移线场理论中有关剪胀的描述,推导了平面应变条件下考虑剪胀角影响并与Mohr-Coulomb准则精确匹配的广义Mises准则,研究了剪胀对浅基破坏模式的影响。
-
The yarns slippages were mainly studied by the forming experiment on cylinder, and yams slippages characteristics were described.Finally, the forming experiments of MBWK fabrics on double-hemisphere were carried out for the first time. Based on the experimental results, the forming characteristics of MBWK fabrics on double-hemisphere were described.
最后,针对女用避弹衣的实际需求设计并进行了双半球成型实验以研究其成型特点及规律,实验中发现织物在成型过程中并无明显的纱线滑移现象,并且其成型规律与双半球之间的间距无关,而仅仅与双半球的直径大小相关。
-
Slip line is a kind of surface defect which occurs in the forming of automobile panel and affects surface quality of automobile panel and appearance of body.
滑移线是汽车覆盖件冲压生产中经常出现的一种表面缺陷,它严重影响了覆盖件的表面质量和车身的外观。
-
A new way of exchange between rotation and reciprocating motion through planetary driving was introduced, which was different from the one realized by piton pump moving with cam, brace and link.
采用行星齿轮传动方式实现从旋转到直线的往复运动,不同于现有柱塞泵由凸轮、曲柄连杆或斜盘实现往复运动的方式,没有滑靴等高压力作用下高速滑移的元件。
-
Currently, the properties of the FRP-concrete interface based on pull-off tests are adopted in the capacity prediction of FRP shear-strengthened reinforced concrete beams.
以往研究中往往简单的将面内剪切试验得到的FRP-混凝土界面粘结滑移关系应用于外贴FRP 抗剪加固梁的剥离承载力计算。
-
A one-dimensional dynamic model is developed for the working fluid in the boiler tube, it is convenient to be connected with furnace model, in order to simulate the dynamic differences of the in-tube working fluid at different positions of the furnace.
在建立的管内工质动态模型中考虑了两相区内汽水之间的相对滑移,以及流体动量沿流程、随时间的变化对动态特性的影响;对过冷区、饱和区和过热区都采用了分布参数模型。
-
Common rolling plank is shown intense (orientaton of 0002) tool reference plane, after rolling of horn waiting for diameter, plank grain orientaton by original (change of orientaton of 0002) tool reference plane is; of orientaton of blame tool reference plane the existence after strain crack of common rolling plank is many twin brilliant, amount of brilliant of twin of drawing of direction of rolling of edge of plank of rolling of horn w
普通轧制板材呈强烈的(0002)基面取向,等径角轧制后,板材晶粒取向由原来的(0002)基面取向转变为非基面取向;普通轧制板材拉伸断裂后存在大量孪晶,等径角轧制板材沿轧制方向拉伸孪晶数量明显减少,等径角轧制有可能启动了新的滑移系,而拉伸孪生只是作为一种协调变形机制。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。