滑移

As the twinborn shear department of {112}m is obstructed, slipping department {111}P of parent phase begin to work, rely on dislocation"s slipping, coordinate flaky martensite"s twinborn shearing and form dislocation inferior structure at M phase corresponding plane(contain the interface between parent phase and martensite phase).

在本实验电镜照片上可以观察到在片状马氏体亚结构同时存在相变孪晶和形变孪晶，当{112}_m孪生切变系受阻时，母相中滑移系{111}_p启动，依靠母相中的位错滑移协调片状马氏体的孪生切变。

The coefficient of friction in the partial slip regime is lower than that in the mixed fretting regime and gross slip regime .

混合区和滑移区的摩擦系数高于部分滑移区。

The author also studies the relationship between the maximum friction coefficient, optimum slip ratio, friction coefficent with locked wheels and three parameters in friction coefficient function of slip ratio, and three fit functions derived from experimental analysis, maximum friction coeffient, optimum slip ratio and friction coefficent v~ ith locked wheels, of aircraft speed.

利用试验数据研究了最佳滑移率、结合系数最大值和机轮抱死时的结合系数随飞机速度的变化规律。两者联系在一起，便得到了结合系数随飞机速度和滑移率的变化规律。它是本文的创新点之三。

The result indicates the wheels dont lock on every road surface, as shows the ability of avoiding the wheel locking. The values of slide ratio approach and revolve round the best slide ratio constantly, which indicates this method utilizes the character of pavement thoroughly, and the braking efficiency is excellent.

结果表明在各种路面车轮几乎没有抱死，显示了自寻优避免车轮抱死的能力；滑移率的值基本上一直接近并围绕最佳滑移率变化，说明该方法充分利用了路面性能，制动性能较好；制动力矩及制动力随着路面条件的变化自动做出相应调整，实现了路面自动识别功能。

The numerical results of yield strength, based on considering the lamellar microstructure and the deformation mechanisms such as ordinary slip systems and true twinnings in PST crystals composed of and phase, is obtained by using calculating of resolved shear stresses in all slip systems based on micromechanical method.

基于PST晶体的微结构和相及2相普通位错和孪晶滑移启动，结合细观力学方法，通过数值模拟两相中的各滑移系上的分切应力，得出PST晶体屈服应力和外加载荷与片层之间夹角的关系。

Based on displacement-based finite element models proposed, a finite element method of steel and concrete composite beams considering slip between steel girder and concrete plate is presented.

摘要利用考虑滑移的钢－混凝土组合梁单元，建立了考虑滑移的钢－混凝土组合梁有限单元法。

The temperature of flue gas out of air preheater in boiler is normally about 120～180℃, the flue gas enter the absorb tower from the bottom via pre-deduster and is accelerated by venturi tube at the bottom of absorb tower, then is taken to circulating fluid bed. The materials are in the circulating fluid bed, due to the effect of flow, the gas-phase and solid-phase generate fierce turbulence and combination and are fully contacted, then form polymers constantly during the ascending and return downward, while the polymers are constantly disassembled during fierce turbulence and elevated by airflow, which makes the slip velocity between gas and solid reach the tenfold times of single slip velocity.

首先从锅炉的空气预热器出来的烟气温度一般为120～180℃左右，通过预除尘器后从底部进入吸收塔，然后烟气通过吸收塔底部的文丘里管的加速，进入循环流化床，物料在循环流化床里，气固两相由于气流的作用，产生激烈的湍动与混合，充分接触，在上升的过程中，不断形成聚团物向下返回，而聚团物在激烈湍动中又不断解体重新被气流提升，使得气固间的滑移速度高达单颗粒滑移速度的数十倍。

We need to know a little about torque, traction and wheel slip before we can understand the different four-wheel-drive systems found on cars.

1，力矩，附着力和车轮滑移 Torque， Traction and Wheel Slip 在学习不同的四轮驱动系统之前，我需要了解一些力矩，地面附着力和车轮滑移方面的知识。

The slip line solutions of stress field and velocity feild on plane strain problems are derived.

推导出考虑各向异性损伤的平面应变问题应力场的滑移线解和速度滑移线解。

Following the theory of slip line field , the area is divided into five sections and the distributing situation of the slip line in each section is analysed.

通过对方盒形件塑性变形过程的分析及变形区域内的变形应力分析，采用滑移线场理论的分析方法，把变形区划分为Ⅰ～Ⅴ区域并分析了这些区域的滑移线分布情况，导出了对数螺线的基圆半径和基圆中心位置及力学模型，为方盒形件的毛坯尺寸的确定提供了依据。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。