滑移

For different materials,the macrostructure of damage sites are dissimilar.The microstructure of damage sites were indicated as follows:the damages of granite and marble after being particle impacted were made up of damage of cleavage surfaces and crystal faces and spread of cracks along phase interface and pore space,which is harmful to mechanical property;while the damages of concrete and mortar were made up of cracks of transition zone and aggregates and plastic flow of C-S-H,which may cause more hidden danger to perma nence than to mechanical properties.

对四种材料损伤形貌的微观分析表明：花岗岩、大理石受颗粒冲击后产生的损伤主要为拉应力导致的解理面、晶面的破坏以及裂纹沿相界面和孔隙的扩展，对其力学性能有较大的危害；混凝土和砂浆的损伤由过渡区开裂、骨料破裂和C-S-H的塑性滑移共同构成，对耐久性造成的隐患远大于对力学性能的影响。

To study the bond-slip performance between structural steel and concrete, eleven short columns with the different configuration are tested, such as cross section dimensions, bond length, concrete strength, thickness of concrete cover and the rate of stirrup lateral.

为研究型钢与混凝土的粘结滑移性能，对11根不同截面尺寸、粘结长度、混凝土强度等级、保护层厚度、配箍率的型钢混凝土短柱进行了试验。

The released species may facilitate and accelerate their detachment and diminish the initial elastic range of bone cement. This may create loosening or shrinking effect on the inserted stem. A conclusion for both behaviors suggest that a variation of relative and dynamic interface in use.

在骨泥与钛金属之长时间微幅运动作用下，骨泥材料受到压力、微幅运动及摩擦热的影响，其表面出现残屑堆积、热软化压平等现象，使得骨泥与钛金属界面产生滑移，进而产生残屑及粗糙度的改变。

Occurs when the semi-finished, warping, especially the post-mounted corrugrted semi-finished products, immediately after the closing of embossing plate, on the paper--and there is no uniform die to tilt paper with the sponge rubber or contact, so easily make embossing plate produced by 印张 bliding, die-cutting production phenomenon.

当半成品出现卷曲、起翘情况时，特别是经过裱贴以后的瓦楞纸板半成品，放在压印平板上合压时，纸面与模切版没有均匀接触，使翘起的纸面先与版面上的橡胶条或海绵接触，这样容易使压印平板上的半成品印张产生滑移现象，造成产品模切不准。

Loader/backhoes, articulated trucks, excavators, motor graders, wheel loaders, vibratory compaction rollers, crawler dozers, skid steers, loader/tool carriers, rough-terrain forklifts, telescopic handlers, trenchers, and horizontal directional drills.

凯斯提供全系列工程机械，产品包括世界第一的挖掘装载机，铰接式自卸卡车、挖掘机、装载机、平地机、振动压路机、推土机、滑移装载机、越野叉车、伸缩臂式多功能车、挖沟机、水平定向钻机等。

Firstly the distribution of the interfacial shear stress of the intermediate crack zone is presented based on the bilinear bond-slip model for the interface between FRP and concrete, Then, theoretical models to predict the load at initiation of debonding and deboning failure are proposed, respectively. Finally, experimental results validate the prediction models.

基于FRP-混凝土界面粘结滑移的双线性模型，推导弯曲裂缝间界面的粘结剪应力，提出了预应力FRP片材加固RC梁由弯曲裂缝引起界面开始剥离以及发生剥离破坏的预测模型。

Map3D Fault-Slip - elastic rock mass and fully plastic fault-slip stress analysis.

Map3D故障滑移-弹性岩体和充分塑料断层滑动应力分析。

Results showed that the ductility of bolt spjice is much better than welds, weaker splice joints develop larger plastic deformation, slipping between faying surfaces, bearing of bolts to hole surfaces and buckling of splicing plates are all ideal energy dissipation mechanism.

试验结果表明：螺栓拼接节点的延性远好于梁柱焊缝连接；较弱的拼接节点产生较大的塑性变形；接触面的滑移、螺栓与孔壁的挤压和翼缘拼接板的屈曲都具有良好的耗能能力。

Results showed that the ductility of bolt splice is much better than welds, weaker splice joints develop larger plastic deformation, slipping between faying surfaces, bearing of bolts to hole surfaces and buckling of splicing plates are all ideal energy dissipation mechanism.

试验结果表明：螺栓拼接节点的延性远好于梁柱焊缝连接；较弱的拼接节点产生较大的塑性变形；接触面的滑移、螺栓与孔壁的挤压和翼缘拼接板的屈曲都具有良好的耗能能力。

The results show that the friction coefficient and slip rate can derived from the test, which benefits the understanding of ABS operation principle and development of relatebed control technology.

结果表明，采用实际测试分析，可以得到制动过程中摩擦系数和滑移率的具体值，它有助于对ABS实际工作情况的了解和相关控制技术的研究。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。