滑动

Coulomb failure stress changes produced by former earthquake on fault plane and slip direction of latter earthquake have been calculated. We found that the number of earthquake doublets with positive CFS change is more than that of negative CFS change.

计算了前面地震事件在后续地震断层面和滑动方向上产生的库仑破裂应力变化，发现正库仑破裂应力变化的"地震对"数多于负库仑破裂应力变化的"地震对"数。

Key slid aside and she felt around under herself, and found his drumsticks under the tangled sheets.

/ 钥匙在一边滑动，而且她在她自己之下在附近感觉，而且发现在被使缠结的张下面的他鼓槌。

DUX M53 had PPS-43 style safety, located in front of the trigger guard, while M59 had a sliding safety switch on the left side of the receiver, above the pistol grip.

的DUX M53了聚苯硫醚- 43式的安全，防范触发位于前面的，而M59手枪握了安全左侧滑动开关就上述的接收器。

With this model, the effects of vertical dynamic resistance on the performance of sliding bearing are deeply explored.

在此基础上，应用这种滑动支座模型，对橡胶支座直接放置于墩顶，与墩顶和梁底的接触面没有螺栓连接，水平力的传递靠接触面的摩擦作用，这种比较常见的桥梁结构形式，做了结构分析，指出其动力性能特点。

A new adaptive recursive algorithm for eigenvector estimation based on the relations between KLT and sliding DCT was presented.

基于KLT与滑动DCT的相似关系，提出了一种新的特征向量自适应递推估计算法。

Generally, its operating condition is under the low-speed and thin oil lubrication, so the viscous friction was usually neglected and the friction torque caused by main influencing factors of elastic hysteresis in rolling, spin of rolling element and sliding friction on contact zone were considered.

低速灵敏球轴承小而稳定的启动力矩和动态力矩对于导航系统的姿态控制至关重要，其工况通常是低速稀油润滑，黏性摩擦被忽略而重点推导接触区因弹性滞后、自旋及差动滑动引起的摩擦力矩。

Film or paper surface dirty, and wrapped it into the dust or clear plastic mulch films after the crease or relaxation phenomena, film hemming switched to a new membrane drying temperature is too high, adhesive surface crust adjust oven temperature, clear crusts partⅱ thermotolerance cohesion and not enough use better glue wrinkle of polymer-coated film transfer after the roll is not the proper balance of films at both ends are inconsistent or wave; adjustment layer of polymer-coated machine too thick, solvent evaporation incomplete, viscosity, pressure drum extrusion, paper (Business card printing and membership card making products) and films between slide to adjust the film covering technology electrothermic roll and rubber roller ends is not plain, pressure is inconsistent, ranging from the adjustment of the linear speed of the machine after the temperature inside the plastic mulch film covering the subject in yellow glue resin particularly resin or additives not resistant to ageing, in the light, heat, under the influence of ultraviolet radiation, chemical change, build the pigments should be switched to a new glue

薄膜或纸张表面不干净，裹入灰尘或杂质清除后再行覆膜薄膜有折皱或松驰现象，薄膜卷边换用新膜干燥温度过高，粘合剂表面结皮调整烘道温度，清除结皮胶的粘接力和耐热性不够换用更好的胶水覆膜后起皱薄膜传送辊是否不平衡；薄膜两端松紧不一致或波浪边；调整覆膜机器胶层过厚，溶剂蒸发不彻底，影响了粘度，受压力滚筒挤压，纸张与薄膜之间产生滑动调整覆膜工艺电热辊与橡胶辊两端不平、压力不一致、线速度不等调整覆膜机器覆膜后易变黄胶水中的主体树脂特别是一些增粘树脂或助剂不耐老化，在光、热、紫外线的影响下，发生化学变化，生成有色物质应换用新胶水

But this method doesnt apply to the analysis of the stability of high fills embankment soaked in water .

通过分析本文探讨了浸水高填方路堤最危险滑动面的形式和位置以及路堤边坡稳定性分析较为合理的方法；1。

Objective To develope a Slide-Traction Plate of epiphysis in Child, which can give the fracture a hard internal fixation, and will not restrain the growth of epiphysis.

目的：研制一种可随青少年儿童骺板生长而滑动的新型钢板，该钢板能保持骨折稳定，随骨骼生长而相应延长、对骺板生长无抑制。

The first one is an algorithm with terminal sliding mode equality constraint. The second is a dual-mode control scheme, which enlarge the terminal region. The sliding mode based MPC is implemented while system state is outside of terminal region, and sliding mode variable structure control designed off-line is used once system state arrives in the terminal region.

第一种方法为终端滑模等式约束非线性模型预测控制方法，首先离线设计切换函数使得滑动模态渐近稳定，然后在有限预测时域的基础上对切换函数附加一个终端等式约束；第二种方法为双模控制方案，在终端区外采用模型预测控制，使得系统状态在有限时域内到达终端区内；在终端区内部采用离线设计的滑模变结构控制，使得系统渐近稳定。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。