滑

The author also studies the relationship between the maximum friction coefficient, optimum slip ratio, friction coefficent with locked wheels and three parameters in friction coefficient function of slip ratio, and three fit functions derived from experimental analysis, maximum friction coeffient, optimum slip ratio and friction coefficent v~ ith locked wheels, of aircraft speed.

利用试验数据研究了最佳滑移率、结合系数最大值和机轮抱死时的结合系数随飞机速度的变化规律。两者联系在一起，便得到了结合系数随飞机速度和滑移率的变化规律。它是本文的创新点之三。

All Slides have: Lamina Wear Plates, Hardened Gibs, Hardened Heel Blocks, and Slide Retainers.

所有滑块要有：薄板，加强的凹形楔，加强垫块，以及滑块回复系统。

Synoviocytes were incubated with different concentration of methotrexate and total glucosides of paeony respectively or combined.

利用mtt比色法测定不同浓度的甲氨蝶呤和白芍总苷单独或联合作用于滑膜细胞，对滑膜细胞增殖的影响。

Pliocene-Quaternary faulting in grabens around the Ordos block displays predominantly normaldip slip displacements with a right-lateral or left-lateral slip component,indicating a NW-trending extension.

鄂尔多斯周缘地堑系上新世～第四纪的断裂作用表征为以正向倾滑活动为主，同时具有右旋或左旋走滑分量的运动型式，指示了NW-SE向地壳引张作用。

Among the slope instability types, thaw slumping is the most hazardous to engineering projects. The ground temperature data of long-term monitoring in the typical thaw slumping indicates that average ground temperature increases and annual fluctuation of ground temperature are reducing under the thaw slumping. The reason is that the heat flux entering permafrost reduces.

针对典型热融滑塌进行的温度监测资料表明，在滑塌的影响下，其下多年冻土地温年变化幅度趋小而年平均地温升高，导致产生这一现象的原因在于每年进入多年冻土的冷能有所降低。

First to analysis original data, including the properties of the material and technological characteristics of the plastic part, then decide the divide surface of cavity and the arrange way of mold cavity, designing the side take out core outfit and guide runner and slide block, still carried on the calculation towards modeling part, cavity deep and thick, hot up and cooling, at last, check the data of injection molding machine.

首先分析原始资料，包括塑件材料的性能和结构工艺特点，然后确定分型面和型腔排列方式，接着设计侧抽芯机构以及导滑槽和滑块，还对成型零件、型腔壁厚、加热和冷却等进行了计算，最后对注塑机进行校核。

First to analysis original data, then decide the divide surface of cavity and the arrange way of mold cavity , designing the side take out core outfit and guide runner and slide block , still carried on the calculation towards modeling part, cavity deep and thick, hot up and cooling, at last ,check the data of injection molding machine.

首先分析原始资料，然后确定分型面和型腔排列方式，接着设计侧抽芯机构以及导滑槽和滑块，还对成型零件、型腔壁厚、加热和冷却等进行了计算，最后对注塑机进行校核。

First to analysis original data, including the properties of the material and technological characteristics of the plastic part, then decide the divide surface of cavity and the arrange way of mold cavity, designing the side take out core outfit and guide runner and slide block, still ca

首先分析原始资料，包括塑件材料的性能和结构工艺特点，然后确定分型面和型腔排列方式，接着设计侧抽芯机构以及导滑槽和滑块，还对成型零件、型腔壁厚、加热和冷却等进行了计算，最后对注塑机进行校核。

Never hit hard on the surface of the aluminum slide rail with steel hammer.

安装时严禁用铁榔头猛击铝滑轨表面，这样会导致滑轨变形。

According to energy balance of thermal systems, based on the Method of Equivalent Heat Drop, a mathematical model applied to thermo-economic comparison is builded.

同时，分析了定、滑压运行经济性比较的特点，依据热系统的热平衡方程组，在等效热降法的基础上，建立了定、滑压运行经济性指标比较的数学模型。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。