温度

The air temperature change in winter was accord with the change of the annual average air temperature.

冬季温度变化与年均温一致，但夏季不同，90年代以前夏季温度是降低的，到90年代夏季温度上升趋势十分明显。

The results show as follows:(1) The characteristical parameters are given out during MSW pyrolyzes as follows: the beginning temperature of quick weight loss, peak value of weight loss, beginning temperature of slow weight loss and weight loss rate of pyrolysis in different temperature etc.

结果得出：(1)垃圾热解时得到特性参数：开始快速失重温度、失重峰值、慢速失重温度、不同温度下垃圾热解的失重百分数等。

In this paper, we used molecule dynamics simulation technique in researching dielectric property. By analyzing the information that is provided from molecule dynamics simulation, we can got some dielectric properties like dielectric constant and chargeability. Firstly, 3D model of silicon dioxide was been built and geometric optimization was been used to make the model more correctly. Then the model was been put in calculation of molecule dynamics simulation with a definitive temperature.

本文针对氮化硼晶体在极端高温下的介电性能开展研究，首先建立六方氮化硼晶体的微观结构模型，通过几何优化对其进行进一步的结构修正，然后选择合适的力场、系综、积分时间步长和压力温度控制方法，对微观结构模型进行某一温度下的分子动力学计算，动力学计算达到平衡后得到该温度下电介质材料的微观结构模型和动力学特性。

By choosing suitable initiator, cure temperature and postcure temperature of 4, 4'-bimaleimidodiphenylmethane /3, 3'-diallyl-bisphenol A , Ciba-Geigy XU292-like BMI system, are greatly decreased to 160℃ and 180℃, and the heat resistance property of cured resins is not decreased.

针对BMI树脂固化温度高的缺点，选择了有效的引发剂，首次大幅度地降低BMI/DP树脂的固化温度和后处理温度（分别降至160℃和180℃，且不降低树脂的耐热性。

The influence of free surface on tunnels is discussed.The influence of blasting vibration on fresh concrete lining is studied. The finite element method is employed to analyze the spatial distribution of temperature and thermal stress of fresh concrete lining, the wave function expansion method is used to study the interaction of blasting seismic wave and the circular tunnel with lining, thenthe safe PPV of fresh concrete lining with different age is decided by taking into account the thermal stress of concrete lining. Using the conformal mapping method, the influence of blasting vibration on the arch tunnel with lining is studied and the safe PPV of concrete lining is deduced under different incident angle.

研究了爆破振动对新浇混凝土衬砌的影响，采用有限元法求出了圆形洞室新浇混凝土衬砌内温度和温度应力在空间上的分布及其随时间的变化，采用波函数展开法求解了爆破地震波与有衬砌圆形洞室的相互作用，获得了考虑新浇混凝土衬砌内温度应力前提下不同龄期的新浇混凝土衬砌的安全振速；利用保角变换研究了爆破振动对直墙拱形有衬砌隧洞的影响，得到了爆破地震波以不同角度入射时混凝土衬砌的安全振速。

The present invention relates to an infrared sensor adapted to be stabilized in temperature and an infrared thermometer with an infrared sensor adapted to be stabilized in temperature, more particularly, a clinical thermometer for temperature measurement in the ear.

本发明涉及一种适用于在温度上稳定的红外线传感器，和一种使用这种适用于在温度上稳定的红外线传感器的红外线温度计，尤其用于在耳朵中温度测量的临床用红外线温度计。

Transmission Electron Microscope and other properties testing results show that the complex emulsifier system is the crucial influence factor of the polymerization process and the properties of products. It may influence the coagulum content and reaction rate of the polymerization process, the performance, particle diameter,viscosity, electrolyte stability and storage stability of the emulsion products and the contact angle of the film.The initiator mainly influences the coagulum content and reaction rate.The acrylic monomers mainly influence the solid content, Minimum Film Formation Temperature of the emulsion and the Glass Transition Temperature of the film.The organic silicone monomer mainly influences the water absorption of the film.The reaction temperature mainly influences the reaction rate and conversion.The stirring intensity mainly influences the coagulum content of the polymerization process.

透射电镜等性能测试结果显示：复合乳化剂体系是硅丙共聚乳液的聚合过程及产品性能的主要影响因素，它可以对聚合过程的凝胶率、反应速率以及乳液的外观、粒径、粘度、耐电解质稳定性及贮存稳定性，还有乳液涂膜的接触角等造成不同程度的影响；引发剂主要影响反应速率和凝胶率；丙烯酸酯单体主要影响到乳液的固含量、最低成膜温度以及涂膜的玻璃化转变温度，有机硅单体主要影响涂膜的吸水率等；聚合反应温度主要影响乳液的反应速率和转化率等；搅拌强度主要是影响到聚合过程的凝胶率。

The results show that the flow stress decreases with increasing deforming temperature and increases with increasing strain rate. The flow stress of the alloy during hot compression deformation can be described by constitutive equation in hyperbolic sine function with a hot deformation activation energy of 196.27 kJ/mol. Partial recystallization takes place in the alloys deformed at a high temperature or at a low strain rate, and large number of dislocations and subgrains are observed in the alloy. The elongated grains observed in the samples coarsen with increasing temperature and decreasing strain rate. Correspondingly, the subgrain size increases and the dislocation density decreases. The main soften mechanism of the alloy transforms from dynamic recovery to dynamic recrystallization.

结果表明：Al-Cu-Mg-Ag耐热铝合金在热压缩变形中的流变应力随着温度的升高而减小，随着应变速率的增大而增大；该合金的热压缩变形流变应力行为可用双曲正弦形式的本构方程来描述，其变形激活能为196.27kJ/mol；在变形温度较高或应变速率较低的合金中发生部分再结晶，并且在合金组织中存在大量的位错和亚晶；随着温度的升高和应变速率的降低，合金中拉长的晶粒发生粗化，亚晶尺寸增大，位错密度减小，合金的主要软化机制逐步由动态回复转变为动态再结晶。

The technique and process for producing differential dyeable and bi-shringkage PET textured yarn are introduced with disscussion on the differential dyeing and shringking mechanism and influence of speed in spinning,spinning temperature,lateral blowing, temperature and humidity of the quench air,spin-finish and its take-up, cold-draw ratio and ratio.

介绍了异染异缩型涤纶变形丝的生产技术及工艺流程，讨论分析了异染、异缩原理和纺丝速度、纺丝温度、侧吹风风速、风温、风湿；纺丝油剂及上油率；冷拉伸倍数、拉伸倍数、拉伸温度、定型温度等工艺参数对其品质和异染、异缩效果的影响。

Combustion parameters such as ignition temperature, peak temperature of maximum weight loss rate, burnout temperature, maximum rate of combustion, and combustibility index were analyzed.

分析了燃烧特征参数如着火温度、燃烧速率最大时的温度、燃尽温度和最大燃烧速率以及燃烧特性指数。采用Freeman-carroll法计算了燃烧动力学参数。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。