温升

So the temperature rising situation is to be diescussed for avoiding the invalidation of the appliances.

因此为了防止部件的失效，必须研究发射过程中战斗部的温升情况。

The numerical calculation results indicate that, when the transitional process has finished, the temperature rising speed of inwall and outerwall is almost a constant, and the temperature difference of inwall and outerwall keeps invariably during laser irradiation.

利用有限元法对金属球壳在恒定功率密度激光辐照下的热效应进行了数值计算，分析了在激光辐照过程中，金属球壳内外壁的温升、温差的变化规律，并主要以铜、铝材料为例，比较了铜、铝球壳在激光辐照下的温度变化和外壁温度响应情况。

JATO JAL636-PL pneumatic cylinder has extremely low temperature rising to avoid thermal error of spindle system of CNC lathes, and it also largely decreases building cost of the machine since no hydraulic pump, tank and cooler is needed.

应用JAL636-PL气压回转缸，数控机床能有效的降低主轴热温升造成的精度误差，并且大幅降低机床本身的建造成本。

This paper has positive significance to the wide application of semiconductor laser diode.

本论文所做的工作对半导体激光器的广泛应用具有积极的意义，它可以克服因激光器原理和工艺方面的限制给应用带来的障碍，比如由于结温升高带来的输出波长的漂移。

The internal Aigh-7c light measurer is to ensure the effect of the cure.

八 固化机内设有过热保护装置，控制机身和光斑区的温升。

Rate of temperature rise was minimal at this point.

率的温升是微乎其微的，在这一点。

The equiv alent viscosity method is used to account for the visco-plastic characteristics of non-Newtonian fluid.

结果表明，热解的摩擦系数明显低于等温解的摩擦系数，当进一步考虑流体的非牛顿效应时，不仅温升的结果更为符合实际，摩擦系数也更接近试验结果。

The system not only can measure the outer and dynamic characteristics and static electric parameters, but also can measure three- phase power factor, input harmonic current and frequency spectrum, and efficiency of arc welding machine.

系统不仅具有测量外特性、动特性、静态参数、电焊机温升等传统电焊机测试台所有的功能，同时还可以测量三相功率因数、输入端电流谐波和频谱分析、弧焊电源效率的功能。

The theoretical model of heat capacity laser output characteristic was established.

建立了描述热容激光输出特性的理论模型，给出了输出功率随激光介质温升及工作时间的变化关系。

To obtain more detailed and accurate temperature distribution inside large size hydrostatic bearing, a simulation method was present, combined with a given example of prevalent applied large size hydrostatic bearing in heavy equipment. It consisted of three dimensional numerical model and boundary condition of hydrostatic sliding way and hydrostatic sliding way inside 3-D flow. The model equations were solved by the Finite Volume Method and by selecting segregated solver of FLUENT according to CFD principle. The more accurate results of temperature rise distribution on periodic surface are obtained. The effect of partial important parameters on temperature distribution was analyzed.

为了能够数值模拟出较详细和较准确的大尺寸静压轴承内部流体的温升分布，以重型装备中所广泛应用的大尺寸静压轴承为研究对象，建立了模拟静压轴承本体及轴承内部三维流动的数学模型及边界条件；利用计算流体动力学原理，采用有限体积法并选取FLUENT中的分离式求解器进行求解，得出了轴承周期端面较准确的不对称温度分布，并分析了部分重要参数对温度分布的影响。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。