深度的

The case depth is the most important quality index of carburized materials, and it is usually checked by selective examination. This traditional method is inefficient and low reliability.

渗碳层深度是衡量渗碳质量的主要技术指标之一，传统的渗碳层深度检测方法是对大批产品采取抽样检查，不仅检测效率低，可靠性差，而且检测时需破坏样品。

At the same time, the relationship between the magnetic flux leakage signals and the physical characters (including the width、depth and position) of the corrosions are studied. The results identify that, if the floor is saturated, the magnetic flux leakage intensity changes linearly with the changing of the corrosion diameter. When the corrosion is in the surface, the peak value of the signal is higher than it's in the back.

同时对缺陷直径、深度以及处于底板上不同位置所产生的漏磁场信号差异进行研究，结果表明，在磁化饱和条件下，平底孔缺陷漏磁场信号峰峰值与孔深度呈线性关系，相同大小的缺陷处于底板下表面时检测信号强度大于处于底板上表面时。

The article,taking Gan Jianhua′s The Iron-willed Sword and GoodPerson Under Heaven for examples,inquires into the depth of in-depth reports which rests with the choice of the cultural perspectives of the reporter.

文章以甘建华两本新闻作品集为例，探讨深度报道的深度在于作者文化视角的选择。

Nautical The depth of a vessel's keel below the water line, especially when loaded

吃水深度：船的龙骨在吃水线下的深度，尤指载重

The best turning tools and parameters of lathe manufacturing magnesium alloy chips are the 31003C with depth of cut 3.5mm and amount of feed 0.4mm, and the 31303C with depth of cut 3 mm and amount of feed 0.3mm.

车床制备镁合金屑料的最佳刀片为31003C刀片和31303C刀片，对应的最佳参数分别为切削深度3.5mm，进给量0.4mm以及切削深度3mm，进给量0.3mm。

Depth of the counter bore for a cap screw in cutting sections is to be equal to height of the head plus die life of sections. If the die sections permit, provide 1 depth to assure that no screw head will interfere with the part after sharpening the section.

刀口入子中沉头螺丝的深度应等于其头部高度加上刃口高度，如果入子允许，提供1英寸的沉头深度，确保当修磨刀口后其不会与产品干涉。

Structure analysis shows that the TiN films have the preferred crystal faces (111) and (200), and the depth of the films is about 20 nm with partial embedding in the substrate.

结构分析显示TiN主要沿(111)和(200)晶面生长，深度分析显示膜的厚度大约二十几纳米，膜质地均匀且在基底有一定的嵌入深度。

Sump Pit Depth for each group of pump s.

每组泵的污水坑深度(深度不同，泵的价格也将有所不同)。

Use the depth guage calibrate the spindle collar step depth and sleeve's height, and make a record for convenient get later processing the spindle front cover preload value.

使用深度表校准主轴深度和步骤衣领的套筒高度，并提出一个新的记录后处理方便获得封面主轴预价值。

To regulate the spindle speed to the stable region can not only make the cutting process stable and achieve excellent workpiece surface, but also improve the metal removal rate by enlarging the cutting depth . The experiment results show that the limit cutting depth can be greatly improved.

将机床主轴转速调整到稳定区工作不但可以使切削过程稳定，获得优良的加工表面，而且可以通过进一步增大切削深度提高机床切削效率，本文对优控主轴转速下机床切削系统的极限切削深度进行了试验考证。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。