润滑

All slideway are mandated centralized lubrication in order to maintain perfect dynamic characteristics with large load-bearing and high precision

机床各导轨均采用强制集中润滑，使导轨具有良好的动态特性，具有承载负荷大，精度高特点

Slideway ; self lubricating composite ; sluice gate ; Three Gorges Project

滑道；自润滑材料；闸门；三峡工程

Applicable for lubrication of rolling and sliding bearings, and other friction parts of all kinds of machineries.

适用于各种机械设备的滚动轴承和滑动轴承及其他摩擦部位的润滑。

Main usages: It applies to lubrication of rolling bearings of various mechanical equipments and sliding bearings and other friction parts.

主要用途：适用于各种机械设备的滚动轴承和滑动轴承及其它摩擦部位的润滑。

Today more and more is being learned about lubrication, that is ,the use of fluids to reduce friction between sliding surfaces.

润滑即是用流体减少两滑动表面间的摩擦。今天人们对此认识越来越深入。

RS+SLINGER type: The SLINGER is fixed to inner ring, rubber seal is fixed to outer ring. The rubber seal and inner ring can form standard torque contact sealing. This combination of two sealing elements can provide an effective barrier against the entrance of foreign matter, such as mud 、 dust 、 vapour, and the leakage of grease to keep the bearing in good working.

防尘盖与橡胶密封圈组合密封：防尘盖固定在内圈上与内圈一起旋转，橡胶密封圈固定在外圈上，密封胶唇与内圈形成标准扭矩接触密封，这种密封能有效地防止外部泥土、灰尘、水气等异物进入轴承内部，同时能阻止轴承内部的润滑脂外漏，使轴承在恶劣的工作环境下也能保持完美的工作性能。

For strong friction or lack of lubricant, please help the slip seat return by upholdingthe gear box manually.

或缺乏润滑使滑座不能完全回位，请用手将减速器向上托，帮助滑座回位。

Main job is to guarantee the scraping interaction and equipment on both sides of the friction surface or can obtain higher precision and accuracy, precision and shape accuracy, precision and contact transmission because of good lubrication, manual and repeatedly is worthy, large amounts of wind, time-consuming, scraping the time needed for different devices vary, such as boring slider and slide block wind profiling, between the match before measuring clearance between the original value, and then according to the technical requirement to measure the value of time and scraping scraping, then apply DanFen red on the slider, manual let slip on the slide seat back and forth, they do straight-line movement between full contact and friction, reoccupy scraper scraping friction creates the contact point, so repeatedly, until the technical requirements for the match, single within 2 days, must blow to the boring if all the time to work with wind, a half month is required.

刮削过程。刮削工作主要是为了保证设备相互接触并摩擦的两面间能获得较高的尺寸精度、形状精度、位置精度、接触精度、传动精度和良好的润滑，因是手工操作且需反复配刮，故工作量大，耗时较长，设备不同，刮削所需时间也各不相同，例如镗床上滑座与下滑座间的配刮，刮削前先测量出二者之间原有的间隙值，然后根据工艺要求测算出需刮削值及每次的刮削量，再将红丹粉涂于上滑座之上，手工让上滑座在下滑座上来回做直线运动，使它们之间充分接触和摩擦，再用刮刀刮削摩擦产生出的接触点，如此反复多次，直至技术要求范围之内，单此项配刮需2天左右，若对于整个镗床所有配刮工作的时间总和，则需半个月左右。

The additives of aloe plant essence and moisture detaining factor make the skin feeling smoothy and refreshing after bath.

添加的海洋精华和保湿因子，使浴后的皮肤具有润滑舒适，清爽之感。

After installing bearing(item 2 and snap ring(item 27)into ring gear(item 6).apply mobll temp 78 grease(2.5oz)to tooth area of ring gear and ball brg.

在把弹簧卡环（项目27）和轴承（项目2）装入齿轮（项目6）之后，在齿轮的轮齿区域和滚珠支座区域上美孚高级润滑脂78号

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。