涂层材料

Three methods,the electrophoresis aggradation,brushed coating and water cooking method were presented to deposit MoS2 coatings in the material surfaces,and the deposited mechanisms were analyzed.

选用电泳沉积法、刷涂法和水煮法3种方法在材料表面制备了二硫化钼涂层，并探讨了3种方法形成涂层的机制。

UV curable coating was used as the dispersion system. The effect of PMMA microspheres, PMMA/TiO2 nano-composite particles and dulling agent on the antiglare property, the viscosity, the mechanical property, as well as the chemicals resistance of the film was studied in this paper. The result showed that the film had better comprehensive property when 0.5% PMMA microspheres, 0.5% PMMA/TiO2 nano-composite particles and 0.75% dulling agent were doped.

紫外光固化体系成膜速度快、涂层透明性好、力学性能优良，本文采用此体系固化成膜，考察了PMMA微球、PMMA/TiO2纳米复合粒子和消光剂对薄膜防眩光性能、涂料黏度、涂膜力学性能以及耐化学药品性能的影响，确定了防眩光涂膜材料涂层的粒子配方：0.5%PMMA微球、0.5%PMMA/TiO2纳米复合粒子和0.75%消光剂。

Test results show that both of the coated specimens have better oxidation resistances than non-coated ones,and surface oxidation decarbonization is one of the leading forms of thermal fatigue damage s.

研究发现，铁基与镍基涂层的抗氧化能力优于铸钢车轮材料，表面氧化腐蚀是涂层试样热疲劳损伤的一种主要形式。

This thesis is organized according to the following outline: firstly, the cause of oxidation localization was discussed in the view of material, both the microstructure and appearance of TGO were analyzed, the element composition of oxidation localization area was probed, combined with oxidation mechanism, the possible influence of oxidation localization on the mechanical performance of TBCs was discussed as well.

本文首先从材料学的角度探讨出现氧化局域化的原因，对TGO层内部的微观结构变化进行跟踪观察，对氧化局域化区域进行成分分析，结合热障涂层体系的氧化机制，讨论氧化局域化现象的出现对热障涂层体系力学性能的影响。

In this paper six kinds of alkyl polyamine polymers which were polyethylene glycol of molecular weight of 400, 600 and 1,000 modified with ethylenediamine or diethylenetriamine were synthesized, and the effects on ink absorption speed, definition and image quality of ink-jetprinting coating layer were studied. At the same time, the better coating formula were found.

本论文合成了六种烷基多胺——乙二胺和二乙三胺改性分子量为400，600以及1000的聚乙二醇所得到的产物，并且研究了它们对喷墨打印材料吸墨涂层的吸墨速度、清晰度及影像质量的影响，最后找出比较理想的涂层配方。

A magnetic storage in which data are stored by magnetic record in g in a film of molecular thickness, coated on a substrate

一种磁性存储器，其中数据以磁记录方式存储在磁性材料涂层上，涂层很薄，涂覆在某种基底上。

Ribbon structure for non-coated paper, coated paper and synthetic materials such as printing object, printing out the ink with excellent fouling and anti-wear scratch test: 680g /㎡.

碳带结构适合非涂层纸，涂层纸和合成材料等列印物件，列印出的油墨具有出色的抗污性，抗磨刮测试：680g/㎡。

The results show that the composite coating is metallurgically bonded to the substrate and the microstructure is fine and uniform. The hardness of the composite coating is up to 400 HV, which is 2.5 times that of the substrate. Under room temperature and oil lubrication condition, the sliding wear tests indicate the friction coefficient and weight loss of the composite coating are smaller than those of substrate. The worn surface of the composite coatings is much smoother than that of the substrate, without grooves and crater.

结果表明，复合材料涂层与基体形成良好的冶金结合，微观组织细小、均匀；复合材料涂层硬度达400HV，约为基体的2.5倍；在室温油润滑条件下，滑动磨损试验表明复合材料涂层摩擦系数和失重均小于基体，磨损表面划痕较浅且平滑，无明显的犁沟、粘着、剥落现象；激光表面合金化显著提高了材料的耐磨性。

The experimental results show that the erosion behavior is similar to that of brittle ceramic materials while the maximum erosion is found to occur at a jet angle of 90 degrees. The successive spalling of splats ...

结果表明：Cr3C2 NiCr涂层的冲蚀磨损呈现脆性材料的冲蚀磨损特征，在 90°冲蚀率最大；磨料冲击引起的裂纹沿涂层内粒子界面萌生、扩展并最终导致粒子剥落，是涂层主要的冲蚀磨损机制。

The study of thermal barrier coatings is the sticking point of exploiting thermal barrier coating system, which is used in the next generation of high performance aero turbine engine.

热障涂层陶瓷材料的研究是开发适用于下一代高性能航空涡轮发动机热障涂层体系的关键，也是未来热障涂层技术发展的重要方向之一。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。