涂层材料

The invention relates the aquosity nanometer polyester- amido resin coating material and preparing method.

本发明涉及化工领域，提供了一种水性纳米复合聚酯氨基树脂涂层材料及其制备方法。

The coating material is prepared with lepidolite 35-55 wt%, potassium feldspar 5-15 wt%, talcum powder 10-20 wt%, soft clay 15-25 wt%, active alumina powder 3-7 wt%, and quartz powder 5-10 wt%, and through mixing into slurry after being added with sodium carboxymethyl cellulose 0.3-1.0 wt%, water glass solution 3-7 wt% and water 30-40 wt%, painting or spraying onto the lining of furnace, drying and sintering at 1200-1300 for 4-12 hr.

本涂层材料在制备时外加羧甲基纤维素钠 0.3～1.0％，水玻璃溶液 3～7％，水 30～40％，将上述混合物经搅拌成均匀的浆体，涂抹或喷涂在炉门内衬材料上，干燥后经1200℃～1300℃下4～12小时的烧成即可制得。

A topcoat material for applying on top of a photoresist material is disclosed.

公开了涂覆在光致抗蚀剂材料上面的面涂层材料。

The effect of main factors such as temperature,chemical composition,and coatings thickness on the properties of titanium carbonitride coatings is also investigated.

氮碳化钛是一种性能优良、用途广泛的非氧化物材料，亦是一种性能优异的涂层材料，它是Ti N和TiC的固溶体，兼有两者的特性和优点[1]。

The developed coating materials and technology would overcome the problem of prebake cells with quite short cell life in China, and could also be found application in innovative aluminum reduction cell as wettable inert cathodic materials.

为了克服我国预焙铝电解槽槽寿命过短的严重弊端，并且发展新型铝电解槽用惰性可润湿性阴极材料，本文在广泛的文献调查和前人工作基础上，对TiB_2复合阴极涂层材料和技术进行了深入的研究。

Based on extensive literature review and previous work in the authors group, further and deeper investigation was performed for cathode materials and technology with TiB2 composite coating. The developed coating materials and technology would overcome the problem of prebake cells with quite short cell life in China, and could also be found application in innovative aluminum reduction cell as wettable inert cathodic materials.

为了克服我国预焙铝电解槽槽寿命过短的严重弊端，并且发展新型铝电解槽用惰性可润湿性阴极材料，本文在广泛的文献调查和前人工作基础上，对TiB_2复合阴极涂层材料和技术进行了深入的研究。

AlPO4 was synthesized by a Sol-Gel method. Its coefficient of thermal expansion was measured by dilatometer. Its corrosion behavior was tested in an environment of 50vol%H2O/50vol%O2 with a flow rate of 0.085cm/s at 1350℃. The phases and composition of the samples were analyzed by X-ray diffraction and Energy Dispersive Spectroscope. The microstructures of AlPO4 were characterized by Scanning Electron Microscope.

采用溶胶凝胶法合成了一种AlPO4环境障碍涂层材料，测定了其热膨胀系数，在1350℃、50vol% H2O/50vol%O2、1.013×105 Pa、气体流速0.085cm/s的水氧耦合环境中研究了其抗水氧腐蚀性能，并利用X射线衍射仪、能谱分析仪和扫描电子显微镜分析了材料组成和微观结构。

However, it is difficult for conventional polys to be used as thin films and coating materials because of their poor solubility.

然而，由于传统的聚芳醚溶解性能比较差，一般很难将其作为薄膜材料和涂层材料进行使用。

Anticorrosive process of surface evaporation air cooler using LLSTD-1 as coating media,which solves two major difficult problems in large scale bundle anticorrosive techniques:performance requirements on coating materials (heat conduction,high temperature resistance,oil-proof and scale inhibition)and the coating method on surface evaporation air cooler bundles.

以LLSID-1涂料为涂层介质对大型表面蒸发空冷器管束进行防腐处理，解决了大型管束防腐的两大难题，一是对涂层材料的性能要求(耐腐、耐温、耐油、阻垢、传热效果好)；二是解决了大型管束防腐工艺(用什么方法将涂料涂装在表面蒸发空冷器管束上)。

Because oxidize the nanometer products of zirconium is high in purity, the activation is good, quality is steady, Can apply to the ceramic field of high technology, the improvement of coating material of function( antimagnetic, environmental protection material ) and traditional material extensively , For instance: Prepare many kinds of ceramic components , carry on the transformation to coating, plastics, rubber material,etc., Improve wear-resisting degree and mechanics characteristic.

由于氧化锆纳米产品纯度高，活性好，品质稳定，可广泛应用于高技术陶瓷领域，功能涂层材料及传统材料的改进，如：制备多种陶瓷元件，对涂料、塑料、橡胶材料等进行改造，提高耐磨度及力学特性。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。