涂层

The results show that the composite coating is metallurgically bonded to the substrate and the microstructure is fine and uniform. The hardness of the composite coating is up to 400 HV, which is 2.5 times that of the substrate. Under room temperature and oil lubrication condition, the sliding wear tests indicate the friction coefficient and weight loss of the composite coating are smaller than those of substrate. The worn surface of the composite coatings is much smoother than that of the substrate, without grooves and crater.

结果表明，复合材料涂层与基体形成良好的冶金结合，微观组织细小、均匀；复合材料涂层硬度达400HV，约为基体的2.5倍；在室温油润滑条件下，滑动磨损试验表明复合材料涂层摩擦系数和失重均小于基体，磨损表面划痕较浅且平滑，无明显的犁沟、粘着、剥落现象；激光表面合金化显著提高了材料的耐磨性。

This paper describes the distribution of potentials and current densities and the chemical changes in the presence of cathodic protection,the mechanism of cathodic protection against crevice corrosion,the mechanism of microbiologically influenced corrosion of pipeline steel beneath disbonded coatings.

综述了在有阴极保护的条件时剥离涂层下缝隙内电位电流的分布和化学环境的变化、阴极保护防止缝隙腐蚀的机理、微生物腐蚀的机理以及前人提出的关于剥离涂层下微生物腐蚀与阴极保护相互作用的规律，并展望了对于解决剥离涂层下微生物腐蚀难题需进一步的实验研究

Silica coating was prepared by atmospheric pressure chemical vapor deposition taking HP40 steel plate as substrate,tetraethyl orthosilicate as silica source,and air as carrier gas and diluent.

以正硅酸乙酯为硅源物质、空气为载气和稀释气，采用常压化学气相沉积法在HP40钢表面制备了SiO2涂层；采用扫描电子显微镜和能量色散能谱表征了SiO2涂层的组织结构和表面形貌；考察了在乙烯裂解的工艺条件下SiO2涂层的结焦抑制能力。

Environmental scanning electron microscopy study showed that PSHA coatings had higher bone apposition ratios than those exhibited by bare Ti-6Al-4V and EDHA coatings after 7 days; however, at 14 days after implantation, EDHA and PSHA coatings exhibited similar bone apposition ratios, much higher than that for bare Ti-6Al-4V.

扫描电子显微镜研究显示第7天时 PSHA涂层的骨沉积比高于裸Ti–6Al–4V合金和EDHA涂层。然而，第14天时EDHA和PSHA涂层的骨沉积比相似，均高于裸Ti–6Al–4V合金。

On the basis of existing study and report, the types of high temperature solid lubricants are renewedly introduced, and the depositing processes of high temperature solid self-lubricant coatings are explained. The concept of designing coatings is introduced, and trend of development of high temperature solid self-lubricant coatings is pointed out.

本文在综合国内外研究和报道的基础上，归纳了高温固体润滑剂的类别划分，阐述了高温固体自润滑涂层和制备工艺的发展，提出了高温固体自润滑涂层设计的概念，指出了高温固体自润滑涂层发展趋势。

The composition, interface and cross section of the sintered EPCD coating were observedand analyzed by SEM, X-ray diffraction , Infra-red spectrum, EPMA, Energydispersion X-ray fluorescence analysis and X-ray-electron spectroscopy,the results show that the coating made from〓BG is composed of HA, titanite and bioglass.

钛合金基体表面的喷砂处理不仅可改善与涂层的机械结合，还可加速其表面氧化和降低预氧化温度，对于实现涂层的低温快速烧结和提高涂层结合强度有重要意义。

Because of having surplus weld reinforcement height and irregular seam form as well as the influences of polyethylene raw materials and coating process, the quality problems of ununiformity in thickness of 3PE coating and coating thickness reduction on helical seam occur.

由于螺旋埋弧焊管存在焊缝余高超高和焊缝形貌不规整等现象，加之聚乙烯原材料及涂敷工艺等因素的影响，会使三层PE防腐涂层出现涂层厚度不均、焊缝处涂层减薄等质量问题。

The role of single wettable Ni and Si、non-wettable SiC and complex SiC+Ni、SiC+Si coatings in Al/C composites on interface wettability、interface reaction and properties of composites was systematically studied in this paper.

论文系统研究了单一润湿涂层Ni、Si，非润湿涂层SiC和复合涂层SiC+Ni、SiC+Si在Al／C复合材料中对界面润湿、界面反应和性能的作用。

Bonging mechanism of coating/matrix and interface bonging of WC-Co/NiCrBSi were studied. Wear mechanism of the composite brazing coating at different wear conditions were proposed.

研究了涂层中WC-Co／NiCrBSi界面、涂层／基体界面连接机制并提出不同磨损条件下复合钎焊涂层表面磨损规律。

Through the contrast cutting test of broaching the internal spiral keyslot of high strength alloy steel workpiece used broaches with and without coatings, the wear properties of broaches and the effect of re polishing rake face on cutting properties of broaches and the workpiece surface roughness are studied.

通过这两种涂层拉刀与未涂层拉刀的对比切削试验，研究了加工高强度合金钢内孔螺旋键槽时刀片的磨损性能及重磨前刀面对刀具切削性能和加工表面粗糙度的影响，并分析了提高涂层刀具寿命的机

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。