浸渍剂
- 与 浸渍剂 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
A copolymer emulsion used for air filter paper impregnation was studied, the emulsion was prepared by copolymerization of styrence/bulyl acryl ate and oxidized starch using sodium bisulphate/potassium per sulfate as initiator and sodium doddery sulfate as emulsifier.
摘 要:采用半连续乳液聚合的方法,以亚硫酸氢钠-过硫酸钾为引发剂,十二烷基硫酸钠为乳化剂,合成了一种以氧化淀粉、苯乙烯和丙烯酸丁酯为主要原料的空气滤清器滤纸浸渍乳液。
-
A new cermet sinter with through micro-porous structure was developed by vacuum liquid phase sintering method, in which Al2O3-Ni-Cr-Mo-Si-Fe powder was used as the basic material, TiH2 and CaCO3 were used as the composite pore-forming materials and hominess grains was used as dispersal particles. The cermet sinter was then infiltrated with Ag-Cu-Pb-Sn at vacuum and formed a new high temperature self-lubricating material.
以TiH2和CaCO3为复合造孔剂,以硬质微细颗粒为惰性弥散质点,采用真空烧结法制备出具有贯通型微孔结构的Al2O3-Ni-Cr-Mo-Si-Fe系金属陶瓷烧结体,并在烧结体中浸渍Ag-Cu-Pb-Sn系浸渍型固体润滑剂制备出新型高温扩散自润滑材料。
-
The conditions and mechanism of Zn2+ loaded on zeolite 13X and alumina werestudied by the orthogonal test. A series of desulfurizing adsorbents were prepared withzeolite 13X, alumina and 5A molecular sieves loaded with Zn2+ and Cu2+ by themethod of impregnation at ambient termperature and desulfurizing capability of thosewere investigated in model gasoline.
采用正交试验的方法,研究锌离子在 13X 和活性氧化铝上负载条件及锌离子负载机理,并采用室温浸渍法,将锌离子和铜离子负载于 13X 分子筛、活性氧化铝、5A 分子筛上,制备了一系列改性型的脱硫吸附剂,考察了这些脱硫吸附剂在汽油模拟体系中的脱硫性能。
-
By means of maceration-wave, added rare earth and CTMA to the bentonite, which produced a new absorbent. The adsorbent behaviour of adsorbent on phosphonium was discussed.
通过浸渍微波辐射法制备镧和CTMA改性的稀土吸附剂,探讨了吸附剂对磷的吸附性能。
-
The result showed that the optimal condition of inorgano-absorbent manufacture as following: concentration of vitriol is 15%, the bentonite carrier must be soaked in the 0.4% La(superscript 3+) solution, the pH is 10, microwave radiation power is 340 W for 5 min. The optimal condition of organo-absorbent manufacture process as following: concentration of CTMA is 5%. The rate of wave must 166 W and the time of radiation is 6 mi In addition, the experimental results showed that with inorgano-absorbent the pH number is 3~6 and the reaction time is 45 min, the removal efficiency of phosphor will be up to 99% and the amount of adsorption will be up to 41 mg/g. And with organo-absorbent the pH number is 3~4 and the reaction time is 45 min, the removal efficiency of phosphor is more 30% than that of inorgano-absorbent. The removal efficiency of phosphor will be up to 99% and the number of adsorption will be up to 60 mg/g.
实验表明:①制备无机稀土吸附剂的适宜条件为:硫酸浓度15%,镧浓度0.4%,浸渍pH值10,微波功率340 W,辐射时间为5 min;②制备有机稀土吸附剂的适宜条件为:表面活性剂浸泡浓度为5%,微波功率为166 W,微波辐射时间为6 min;③无机稀土吸附剂当溶液的pH值为3~6,振荡时间为45 min时,对磷去除率为99%以上,吸附量达到了41 mg/g以上,有机稀土吸附剂当溶液的pH为3~4,振荡时间为45 min时,其效果比原来镧改性的无机吸附剂吸附量提高了30%,磷去除率为99%以上,吸附量达到了60 mg/g以上。
-
The method for manufacturing the filter includes the steps of immersing a supporter in a suspension in which the powder of the fraipontite mineral and the powder of an inorganic substance as a binder are dispersed as the suspensoid, and drying the supporter impregnated with the suspensoid, thereby forming an inorganic material layer fixed to the surface of the supporter.
制造该过滤器的方法,包括将载体浸渍在悬浮液中的步骤,在该悬浮液中将丝锌铝石矿物粉末和作为粘结剂的无机物质粉末分散成悬浮肢体,和干燥用该悬浮胶体浸渍过的载体的步骤,从而制成固定到载体表面上的无机材料层。
-
Sulfide precursors were synthesized by conventional inorganic metal salts and a sulfurizing agent. Sulfide catalysts were prepared by isochoric impregnation using an impregnation solution containing sulfide precursors and a dispersion additive.
以常规金属无机盐及硫化剂为原料合成硫化物前驱体,在硫化物前驱体溶液中加入添加剂配成浸渍液,浸渍载体制成硫化型加氢催化剂。
-
In comparison of the National Standard of insulating paper, the results show that the guanidine condensed phosphates show the good flame retardancy in the insolating paper and a little effect on other properties, which conforms to the ...
通过与国家标准进行比较结果表明,该阻燃剂对浸渍绝缘纸进行阻燃处理后,不仅能获得良好的阻燃性能,而且对浸渍绝缘纸的其它性能影响小,并符合国家标准。
-
On the basis of dopping carbon anode by soaking, the preparation of dopping solvent by mechanical mixing method and their electrocatalytic results are studied.
在原有的浸渍法掺杂碳阳极的基础上,全面考察了机械混合法掺杂碳阳极的掺杂剂制备和掺杂效果,并将其与浸渍法掺杂进行了比较。
-
The epoxy sheet-like mold plastic comprises the following parts: 100 quetient mixed epoxide resin, 4-10 quetient deflocculating agent, 15-80 quetient curing agent, 5-20 quetient thickener, 1-4 quetient internal releasing agent, 80-180 filler and 50-150 fiber, wherein the intermediate core material of the epoxy sheet-like mold plastic comprises fiber which is dipped epoxide resin paste, and the up-down surface is covered by PE thin film.
该环氧片状模塑料,其中间芯材是由浸渍了环氧树脂糊的纤维组成,上下两面以PE薄膜覆盖;按重量份数计,由以下原料制成:混合环氧树脂100份,稀释剂4~10份,固化剂15~80份,增稠剂5~20份,内脱模剂1~4份,填料80~180份,纤维50~150份。
- 推荐网络例句
-
I can not make it blossom and suits me
我不能让树为我开花
-
When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.
当温度高于 80 °C 左右时,滚道或滚动元件褪色是很常见的特征。
-
The lawyer's case blew up because he had no proof.
律师的辩护失败,因为他没有证据。