浸入的

My feeling shows that my bad heart entre into the perfect comfort,which is similar with asphodel after summer and fall,repeatly immerge into the purified water,feel as if thinker is comfortable and passion.

我觉的，这时自己久蒙尘垢的心灵顿然浸入了一片慰藉之中，就像经历了夏秋后的水仙球，重新浸入那纯净的清水之中一样，心智舒展，活力洋溢。

Airport management is well aware that water-proof measures to prevent and reduce ground water immersion in order to eliminate the loess collapsibility of external conditions.

机场管理层深知，防水措施是防止和减少水浸入地基，从而消除产生黄土湿陷性的外在条件。

Cor. 1:15 That no one may say that you were baptized into my name.

林前一15 免得有人说，你们是浸入我的名里。

When the debris has collected under the crown cap, the bottles are immersed in brine to freeze their necks. When the cap is removed, the pressure of the gas (60 to 90 pounds per square inch) forces out a plug of ice containing the dead yeast cells.

当残渣聚集瓶口时，将其浸入冷水中使之凝固，移开瓶盖后，气压（60至90磅每平方英尺）会使死去的酵母和汁液一起喷出。

Take test pieces out after holding 28 days, clean it with water and desiccate.

在每种溶液中浸入 3 块按图 1 和表 4 裁取的 I 试片，试片上面离液面至少 20mm，密闭容器，保持 28d 后取出用清水冲洗干净，擦干。

Without being a declared irrationalist,and without to have articulated a"criticism of the reason"in any form,Derrida would have thus contributed to disturb or discredit any exercise of rationality,by immersing it in"the writing".

并非作为某种非理性主义者，也并非简单的"理性的批判"，德里达力图扰乱理性的活动，使之名誉扫地，使之浸入"书写"之中，也就是说浸入虚构、滑稽模仿之中。

Based on this point of view, a mechanism for polymeric membrane formation by immersion precipitation was developed to interpreter the role of nonsolvent additive, which is helpful to select the suitable nonsolvent additive and the amount used for high performance polymeric membrane.

基于上述观点，本文提出了浸入凝胶过程中聚合物膜的形成机理，解释了NSA在浸入凝胶成膜过程中的效应，从而为选择不同的NSA和加入量，制备高性能的聚合物膜提供理论指导。

A water model for simulation of 1050 mm mold is established to investigate the effects of SEN structure, casting speed, immersion depth and other parameters on the fluctuation of the liquid level in the mold, the impact depth of the steel stream and entrapping of the flux, and compare the influence of different structure parameters and operating parameters on the flowing field in the mold in order to find out the best suitable compromise between the structure parameters and the operating parameters and then...

针对 10 5 0mm× 15 0mm断面的结晶器，建立了水模型，研究浸入式水口结构、拉速、浸入深度等工艺操作参数对结晶器液面波动、流股冲击深度及结晶器钢液面保护渣卷入情况的影响，比较不同水口结构参数及操做参数对结晶器内流场的影响，从而找出结构参数与工艺参数间配合最佳的工况，为水口设计提供理论依据，并经优化的水口在实际中应用，使安钢第二炼钢厂的板坯退废率由 1.5 0 %降为0 。6 %。

In comparison with bugle shaped nozzle, bifurcated nozzle downward jet angle 45°, cow-nose nozzle and three-hole nozzle, in all, the last two are better than the former and bifurcated nozzle downward jet angle 45 is better than bugle shaped nozzle; Cow-nose nozzle is helpful for guaranteeing the product"s quality, in order to protect jet flow from eroding the strand at narrow face, gain uniform temperature distribution at cross section and decrease heat flux, adding the block"s width to 100 mm. Three-hole nozzle is advantageous to increase flux and casting speed, but should avoid weak shell thickness in the center broad. In the real production, setting the SENs immersed depth or plugging the hole at the bottom can adjust the flow and temperature distribution in the mold.

对比喇叭形水口，双侧孔水口(45°)，牛鼻子水口和三孔水口，总的说来后两者优于前两者；而双侧孔水口(45°)又优于喇叭形水口；牛鼻子水口和三孔水口比较各有特点，前者对保证铸坯质量有利，为防止流股对窄面的冲击，增加挡块宽度到100 mm，可使结晶器横截面上温度分布更加均匀，降低窄面热负荷；后者对增加流量，提高拉速非常有利，但要防止中孔射流过强导致铸坯中心坯壳变薄，在实际生产中可通过控制水口浸入深度或塞住浸入式水口的底孔来调节结晶器中的流动与温度分布状态。

Ideal Kaehlerian slant immersions in a complex space form are also proved to be minimal, which is a natural generalization of Chen's result.

另外对于复空间形式中的Kaehler slant浸入，如果它是理想的，则必是极小浸入，该结果是Chen定理的自然推广。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。