浇铸
- 与 浇铸 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Antonio Susini, is the most important bronzesmith moulding, who trusted by the master deeply, Giambolognasent him to Rome to study archaic enchase, this experience gave Susini's products denseness classical temperament.
安东尼奥·苏西尼,是意大利样式主义时期最重要的青铜浇铸师和雕刻家之一,他曾追随詹波洛尼亚多年,为大师浇铸青铜雕塑,深得大师的信任,詹波洛尼亚曾亲自送他去罗马学习古代雕刻,这段经历赋予了苏西尼的作品以浓厚的古典气质。
-
The modified equation is especially suitable for use in the weight calculation of easting iron-rol/ring-inserting tubes.
从国外引进的Mc尼龙生产设备中,除有旋转浇铸机外,也附有MC尼龙管浇铸量计算式。
-
The mold is made of the silicone pattern layer with a quartz supporting plate. The parameters in a vacuum casting process and a hardening process for composing the silicone are optimized to improve the physical properties of the mold to keep adequate demold and pattern accuracy.
分析了硅橡胶模具制作工艺中真空辅助浇铸的成型过程,以及交联固化反应过程的各个工艺参数对硅橡胶模具性能的影响,通过大量实验,具体分析了硅橡胶单体和固化剂配比、浇铸真空压力、固化温度及固化时间等工艺参数,并由此得到了优化的硅橡胶固化工艺参数,提高了硅橡胶模具的物理性能。
-
Using poly (4-merhylpentene-l) as a membrane material and cyclohexane, irich-loroethylene, tetrachloroethylene, mixture of cyclohexane and trichloroethylene or tetrachloro-ethylene as solvents, the solution were cast to form homogeneous dense membranes, and the crystalline properties and surface morphology were investigated by DSC and TEM.
以聚4-甲基戊烯-1为膜材质,分别以环己烷、三氯乙烯、四氯乙烯、环己烷/三氯乙烯及环己烷/四氯乙烯为溶剂,研究了这些溶液浇铸膜的结晶性质和表面形态。结果表明,溶剂对PMP的相对溶解能力和挥发速度同所成膜内PMP的结晶形式和结晶度密切相关;不同溶剂体系的PMP溶液浇铸膜的表面形态也不尽相同。
-
The molded character, which is made of Acryl, has below outstanding characters
浇铸字采用液态亚克力单体原料整体浇铸而成,具有以下突出特点
-
And the production comprises that dissolving polyarylamide into organic solvent; mixing and adding alumina particles, disperser, holing agent to be vibrated via ultrasonic wave; putting into drying box to be aged and defoamed; irrigating into film; vaporizing it in drying box; putting into solidify liquid to be emerged; washing with distilled water, processing aminic acid solution, compressing and shaping.
分散剂0.6~8wt。%、成孔剂2~8wt。%组成,制备方法为:将芳香聚酰胺溶于有机溶剂中,在搅拌中加入氧化铝颗粒、分散剂、成孔剂超生震荡;放入干燥箱中熟化、脱泡;浇铸成膜;浇铸后的膜在干燥箱中蒸发,然后放入凝固液中浸泡,接着用蒸馏水漂洗干净后用甲酸溶液处理;最后预压成型。
-
Using the commercial software pack of CFD, simulation of casting process from a 40t ladle is carried out and the law of hot metal flow in the ladle in stand still as well as in the ladle in casting is determined.
利用CFD商业软件,对建立在正交网格上的40t钢包浇铸过程进行了数值模拟,模拟结果得出了钢包静置和钢包浇铸的钢水流动规律。
-
Zirconia/graphite compound mold core was prepared by the coating, in which the silicon sol was used as binder and zirconia was used as refractory materials. The application feasibility of metal particles as a coolant in the solidification process was studied, and the application of metal particles as subsidiary coolant in the liquid metal cooling of directional solidification were analyzed and studied in this investigation. The conclusions can be drawn as follows: 1 The zireonia/graphite compound cores fabricated by brushing coating which was prepared by making silicon sol agglutinated zirconia as a refractory material were casteded at 800℃and 1000℃respectively, and the results show that the strength of the mold core is strong enough to meet the requirement of practical casting.
本文研究了以硅溶胶为粘结剂,氧化锆为耐火材料来制备氧化锆/石墨复合型芯的制备工艺;并分析了金属颗粒作为冷却剂在金属凝固过程中应用的可行性、金属颗粒的冷却能力以及金属颗粒作为辅助冷却剂在定向凝固的液态金属冷却法中的应用,得出以下结论:(1)以硅溶胶为粘结剂,氧化锆为耐火材料来配制涂料,采用刷涂石墨型芯的方法来制备的氧化锆/石墨复合型芯经800℃和1000℃实际浇铸实验,结果证明型芯的强度足够满足实际浇铸要求。
-
The result shows: the material of glass reinforced plastic mortar pipe is brittle, the enlaced sample always destroyed along the interface of different layers, but the centrifugal sample destroyed along a breach; the capacity of bearing radial load of enlaced glass reinforced plastic mortar pipe is better than the centrifugal ones, the destroyed forms of them is also different. Secondly, the whole pipe and direct shear friction experiments between glass reinforced plastic mortar pipe and typical soil of Shanghai have been done.
结果表明:玻璃钢夹砂顶管管材属于脆性材料,缠绕式玻璃钢夹砂顶管的材质试样基本沿着层与层之间的分界面破坏,而离心浇铸式玻璃钢夹砂顶管材质试样的破坏是沿着某个滑裂面破坏;缠绕式玻璃钢夹砂顶管的抗径向荷载性能要优于离心浇铸式玻璃钢夹砂顶管,同时两者在径向荷载作用下的破坏形式明显不同。
-
If ladle pouring, do the ladles have a teapot spout to hold back slag?
如果人工浇铸,浇铸包是否具有茶壶型出口挡渣?
- 推荐网络例句
-
I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""
客人们在卡罗利娜·埃凯家里,举止就文雅一些,因为卡罗利娜的母亲治家很严厉。
-
Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.
由著名品牌 Herm è s 设计,这件高贵的制服是香港本土制造,是我们第一套不配帽子的制服。
-
Do not 'inflate' your achievements and/or qualifications or skills .
不要 '夸大' 你的业绩或成果,条件或者技能。