浇注点
- 与 浇注点 相关的网络例句 [注：此内容来源于网络，仅供参考]
-
This paper analyzes the principle of the LP-LFC process,presents the physical and mathematical models of mould filling of the new process. The patterns including window-plate, ladders cluster, electromotor frame and exhausting manifolds are poured using LP-LFC process with AZ91D alloy, and the mould filling course is tracked with electrode touch point method. Based on above tests and experiments,the casting defects including short runs, cold laps, trapped gas,metal penetration, and so on, were investigated. The appearance characteristics,birth causes and influence factors of above defects are discussed in the article,diagrammatize modes of the defects forming is also given, and the measures of reducing or avoiding defects are put forward.
本论文分析了低压消失模铸造技术的工艺原理，建立了低压消失模铸造过程中金属液充型的物理和数学模型；在各种工艺条件下浇注了薄板窗体、阶梯模样簇、电机外壳和发动机排气管四个典型的模样和产品，用电极触点法记录了镁合金低压消失模铸造的充型过程；试验研究了镁合金低压消失模铸造中出现的浇不足、冷隔、气孔、粘砂等典型缺陷，分析了这些缺陷的形貌特征、形成原因及影响因素，给出了缺陷形成过程的图解模型，提出了减少和消除缺陷的工艺措施。
-
After studying casting process from ladle to pouring box and protection casting supporting mechanical structure, vibration dynamics model of supporting structure is founded, also variation of stee...
通过对钢包到中间包保护浇注的过程及其支承结构的相关研究，建立保护浇注支承结构的振动动力学模型，并且考虑对钢液冲击力的变化及影响测振点振动的因素，利用基本小波处理方法对钢水振动信号进行初步分析，并通过小波包技术进行进一步的特征提取，最终实现对钢液状态的有效识别。
-
After studying casting process from ladle to pouring box and protection casting supporting mechanical structure, vibration dynamics model of supporting structure is founded, also variation of steel water impact force and influencing factors of inspecting spot vibration are discussed. Primary analysis is done for steel water vibration signal by the way of basal wavelet processing method, and the deeply feature extraction is finished to realize the effective recognition for steel water status using wavelet package method.
通过对钢包到中间包保护浇注的过程及其支承结构的相关研究，建立保护浇注支承结构的振动动力学模型，并且考虑对钢液冲击力的变化及影响测振点振动的因素，利用基本小波处理方法对钢水振动信号进行初步分析，并通过小波包技术进行进一步的特征提取，最终实现对钢液状态的有效识别。
-
The key point was the structural design of sliding blocks for shaping,the application of pin point gate and auto-demolding mechanism.
由于塑件结构复杂，设计时注意了点浇口的使用和相应三板式注射模的特点，并采用了自动脱料装置，以利于浇注系统凝料的取出。
- 推荐网络例句
-
They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.
他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。
-
In slot 2 in your bag put wrapping paper, quantity does not matter in this case.
在你的书包里槽2把包装纸、数量无关紧要。
-
Store this product in a sealed, lightproof, dry and cool place.
密封，遮光，置阴凉干燥处。