浇注

The melting speed, overheat temperature, pouring temperature and modification in production of high chrome cast iron were studied.

对高铬铸铁的熔炼速度、过热温度、浇注温度及变质处理进行了研究。

In this way, it is possible to commence linear measurements immediately after casting.

用这样的方法，有可能在浇注后立即开始线性测量。

Under the protection of fusing agent or gas, melting commercial-purity magnesium completely in copple, adding alloying element in formation of Al-Be hardener, commercial-purity aluminum, Al-Mn hardener, Mg-Re hardener and commercial-purity antimony, agitates to achieve uniform mixing, refining and casting.

在熔剂或气体保护熔炼条件下，工业纯镁在坩埚中完全熔化后，分别以Al-Be中间合金、工业纯铝、Al-Mn中间合金、Mg-Re中间合金，工业纯锑的形式加入合金化元素，搅拌混合均匀并进行精炼后浇注。

Using B Grade bauxite as bone material and A Grade bauxite as powder,different binder composition castable for permanent lining fo fundish were studied,with cyanite and sillimanite as expansion additives and Zimujie clay as sinter additive and plastic additive.

以B级高铝矾土熟料为骨料，A级矾土熟料为基质料，同时加入蓝晶石、硅线石为膨胀剂，紫木节粘土为烧结剂、塑化剂，研究了分别采用硅灰、高铝水泥、水玻璃、复合结合剂等为结合剂的不同配方组成的浇注料。

The main functions of the Basic Oxygen Furnace are to decarburize and remove phosphorus from the hot metal, and to optimize the steel temperature so that any further treatments prior to casting can be performed with minimal reheating or cooling of the steel.

转炉的主要功能是脱碳和除磷，并优化钢液温度，使得再浇注之前的任何再处理只要对钢液的加热和冷却做微调节即可。

The process to substitute ferro-silicon-aluminium with ferro-silicon-aluminium-barium as end deoxidizer is discussed.

对河北敬业钢铁有限公司炼钢厂用硅铝钡铁代替硅铝铁作终脱氧剂工艺进行了探讨，认为该工艺是可行的，钢水浇注性能良好，并且可获得明显的经济效益。

The process to substitute ferro-silicon-aluminium with ferro-silicon-aluminium-barium as end deoxidizer is discussed. It is considered the process can be used for production because of the good casting performance of melting steel and distinguished economic profit.

对河北敬业钢铁有限公司炼钢厂用硅铝钡铁代替硅铝铁作终脱氧剂工艺进行了探讨，认为该工艺是可行的，钢水浇注性能良好，并且可获得明显的经济效益。

For die casting systems, the introduction agencies, the cooling system for a detailed analysis of the design.

对于模具的浇注系统、推出机构、冷却系统都进行了详细的分析设计。

For the die casting systems, Launch, cooling systems are a detailed analysis of design.

对于模具的浇注系统、推出机构、冷却系统都进行了详细的分析设计。

The compound steel formwork is widely used because of small volume, light weight and convenient dismounting, but is also limited to use because of poor appearance quality of the concrete poured by it.

组合钢模板因体积小、重量轻、拆装方便而得到广泛使用，但也因使用其浇注的混凝土外观质量差而受到限制。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。