流空

The Large eddy Simulation is used to simulate the flow field and cavitation on an Orifice Energy dissipator. The characteristics of cavitation was analyzed. The calculated and the measured pressure distribution and the cavitation were in agreement.

采用大涡模拟方法对消能孔板流场及空化现象进行了数值模拟，研究分析了消能孔板空化特性，计算所得的压力分布及空化特性与减压模型实验结果进行了比较，二者符合良好。

Based on the theory of cavitating flows,the definition of supercavitation ,the main idea of reducing drag by ventilated cavitation and the principle of supercavitation torpedo are introduced.

文章从空泡流理论出发，介绍了超空泡的定义、超空泡减阻的基本思想和超空泡鱼雷的工作原理，并分析了超空泡技术研究中的关键问题和未来发展趋势

Sub-volcanic rocks include andesitic porphyrite, rhylitic porphyry, cryptoexplosive breccia as well as autobreccia etc.(2) Volcanic lithofacies——through the observation of cores, identification of thin sections and interpretation of well logs and seismic data, there are 8 kinds of lithofacies for the volcanic rocks of Yingcheng Formation are identified: fallout facies, effusion facies, pyroclastic flow facies, base surges facies, lahar facies, eruption-sedimentary facies, subvolcanic facies and extrusion facies.(3) Three types of eruption——i. e. explosion, effusion and surge.(4) Two kinds of eruptive environments——Subaerial (e. g. volcano in Well Shangshen 3) and subaqueous .(5) Three remarkable volcanic apparatus in Shengping-Wangjiatun area——layered, micro-shield and cone volcanoes according to volcanic processes and lithofacies distribution.

次火山岩有安山玢岩、流纹斑岩、隐爆角砾岩及自碎角砾岩等；(2)火山岩相——通过岩芯观察、镜下鉴定、测井与地震资料解释，营城组火山岩中发育8种岩相类型，即爆发空落相、溢流相、火山碎屑流、基底涌流相、喷发沉积相、火山泥石流相、侵出相和次火山相等；(3)火山喷发的形式——有爆发、溢流和涌流三种；(4)火山喷发环境——有陆上(如尚深3井火山)和水下两种；(5)火山机构类型——根据火山作用特点和岩相分布特征，在升平—汪家屯地区识别出三类截然不同的火山机构，即层火山、微型盾火山和渣锥火山。

The solutions were found to be good agrees with experimental results. The transfer characteristic of air dry/wet bulb temperature and spraying water temperature were discussed. The LMTD method based on this mathematical model is applicable to design and verify for the plate wet air cooler. The ratio of the wet bulb heat transfer coefficient to the heat transfer coefficient under air-cooled conditions was investigated theoretically and experimentally. The relative errors of the ratio between theoretical and experimental valves are small than 7 percent.

分别得到了平行流型式微分方程组的解析解与交叉流型式的近似解析解，实验验证了该解析解具有较高的计算精度；探讨了空气干湿球温度与喷淋水温的迁移特性；分析得到基于湿球温度迁移模型的对数平均温差法在湿式空冷器的设计与校核计算中是适用的，给出了空气湿球换热系数与空冷时空气对流换热系数比值的理论与实验确定方法，比值系数理论值与实验值比较最大相对误差小于7％。

Using upwind finite method with the technology of grapy display the artile, solves the leak air seepage and air movement diffusec equation and seepage dissipation equation of oxygen concentration variation process.

结合实例，用迎风有限元方法求解了回采采空区漏风渗流方程和氧气渗流耗散方程，从理论上说明采空区氧浓度分布的不均衡性。

In order to do research on pipe flow and pump characteristics of polymer flooding and water flooding rod-pumped well in especially high water-cut stage, rheometric test aimed at production stream from polymer flooding and water flooding rod-pumped well in especially high water-cut stage has been made, and the characteristic of production stream in especially high water-cut stage is confirmed as Newtonian fluid. Experiments using different mediums about pipe flow and pump characteristics is made. Frictional resistance and coefficient of friction resistance of annulus fluid between sucker rod and the pipe flow is calculated under different working conditions. Frictional resistance between plunger and pump barrel under different parameters is calculated based on related theory of pump characteristic and the strained analytical model of oil-well pump. Besides, using the theory of slit flow and hydraulic -clamping pressure, the frictional resistance is calculated, and the error between the result and measured value is no more than 13%.

为研究特高含水期水驱及聚驱抽油机井管流特性与泵特性，本文针对特高含水期水驱及聚驱井采出液进行了流变性试验，确定了特高含水期油井采出液的性质属牛顿流体；利用不同介质，进行管流特性与泵特性试验，得到了不同工况下杆、管环空流的摩擦阻力和摩阻系数；根据泵特性相关理论和抽油泵受力分析模型，计算了不同参数下柱塞与泵筒间的摩擦阻力，并利用缝隙流与液压卡紧力理论对柱塞与泵筒间的摩擦阻力进行了计算，计算结果与实测值误差在13%以内。

Through 2D axial symmetrical and 3D scarfed reversal nozzle calculating, the main flowfield characters were given, and compared with the experiment data for validation. Then, the program was given, which can well predict the performance of the scarfed reversal nozzle. In this paper, the flowfields of open cavities with different structures and different parameters were calculated. Some new, full and more reasonable mechanism interprets were given. We think that the essential cause of pressure oscillatory is coherent effect of wave, eddy and cavity structure, but the procedure is different with different cavity structure, it can not use single procedure to described.

通过对二维轴对称和三维斜切反喷管的计算分析，本文给出了流场的主要特征，并采用实验数据进行了验证，形成了分析斜切反喷管可靠的应用方法；本文通过对不同结构形式、不同参数的二维、三维非定常超声速开式空腔流动进行的计算分析，提出了较为全面、合理的空腔压力振荡循环机理的解释，本文认为压力脉动本质上是波、涡以及结构之间相互的干扰和耦合，但干扰的具体过程随空腔结构的不同差别较大，不能采用单一的规律进行描述。

Based on the 3D time-average Navier-Stokes equations, k-ε model was used to simulate the 3D turbulent flow field of whole flow passage in the Francis turbine including guide wickets, runner and draft tube. The energy performance and cavitation performance were predicted from the simulation results, and the calculated data were compared with the results of hydraulic turbine model experiment. The calculation of turbine efficiency and the measured efficiency was very closed and the maximal relative error was 0.9%.

该文基于Navier-Stokes方程和k-ε紊流模型，采用贴体坐标和交错网格系统，用SIMPLEC算法对一模型混流式水轮机引水元件、转轮和尾水管进行了联合计算与转轮单流道计算，数值模拟了水轮机各通流元件内部三维湍流流场，预测了水轮机的能量性能和空化性能，并与水轮机模型试验结果进行了对比。

Numerical simulation of the steady cavitating turbulent flow in the whole flow passage of a Kaplan turbine has been carried out by using a full cavitation model and a mixture two-phase flow model.

采用一种完整空化模型和一种混合流体两相流模型，对轴流式水轮机全流道内的定常空化湍流流动进行了数值模拟。

It is requesting (according to its Request/Transmission Policy, as in 11.4.9.13) and being granted bandwidth for transp ort of data packets.

激活业务流的激活Qos采纳数集不为空，激活之前为空。业务流用来请求和分配数据包传输带宽。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。