流溢

In addition, because of the interleaving of top and bottom nappes, there is no bump in the air, the finite width of spillways can be fully utilized, and flood discharging atomization caused by bump of nappes can be weakened.

而且，表、深孔水舌在空中交错穿插，不发生空中碰撞，可充分利用有限的溢流宽度，并减少因水舌空中碰撞而导致的泄洪雾化的增强。

At the same time, large angular acceleration will cause impact in the hydraulic system.

溢流缓冲主要是降低瞬时压力冲击。建立相应的功率状态方程。

Though analysis and comparison,the appropriate angular aperture of runner and the interrelationship between overflow and exhaust system were achieved for the circular die casting.

分析比较得出适合圆形压铸件浇注系统设计时的横浇道张角夹角范围，以及溢流槽与排气槽之间位置尺寸相互影响的关系。

With the different distances between fissures and Laoheishan volcanic cone and the types of lava flows (sheet lava flows or small sub-overflows), the tension fissures show the different features.

随着距离老黑山火山锥位置的不同和熔岩流的类型(如席状熔岩流、小规模次级溢流体)不同，张裂呈现不同的特征。

A hydrodynamical model for oilspill simulation in archipelagic waters with multiple open boundary conditions is set up and simulation/forecast tests in Zhoushan dingpu Port are performed.

初步试验表明，模式重视了港域内许多重要的流体动力学特征，能模拟或预报海域内三维潮流、风生流及其相互作用，并为溢油模拟提供实时流

The equipment provided in process are: jig sorting mainly to deal with overflow flotation, jigging in the coal and coal flotation tail mixed into the power plants, waste shipped to the Waste Dump, block coal jigging dehydration, floating Coal election at the end of filtration and hydraulic flow classification Desliming, dehydration through the belt to the Coal Wharf.

本设备所规定的工艺流程是：以跳汰选别为主，浮选处理溢流，跳汰中煤和浮选尾煤混合入电站，矸石运向矸石山，跳汰块精煤脱水、浮选精煤过滤与水力分级底流脱泥、脱水通过皮带运到精煤仓。

At last, the configuration of a relief valve were improved, the cavitating flow simulation.

最后，对溢流阀阀芯形状进行了改进，通过对不同结构的化实验和噪声测试，实验结果与流场分析结果一致，改进后的阀气穴强度和噪声均得到降低。

LIQUID FLOW MEASUREMENT IN OPEN CHANNELS BY WEIRS AND FLUMES.

NF X10-312-1986 用溢流堰和水槽法测量明渠中的液流。

At last, according to the effect of orifice configuration on the cavitation, the several poppet configurations of a relief valve were designed in order to suppress cavitation, the cavitating flow simulation for different configuration were performed and compared in ordet to find a optimal conriguration.

最后，针对阀口形状对气穴的影响，为了抑制阀口气穴，对溢流阀阀芯形状进行了改进，设计了几种不同的阀芯结构，分别对不同的阀芯进行了气穴流场分析和比较，来寻求优化的阀芯结构。

Traditional plastic injection molding machine relies on constant rate pump in oil supply, and each action in the process of plastic injection may have different requirements on speed and pressure. The surplus oil flows back to the oil tank through the proportioning valve in the way of flooding adjustment. In the whole process, the rotation speed of motor remains unchanged, so the oil volume is fixed as well. Furthermore, the action is intermittent, and not of full load, so a great amount of oil is wasted.

传统的注塑机是采用定量泵供油的，注塑过程的各个动作对速度、压力的要求也不一样，它是通过注塑机的比例阀采用溢流调节的方式将多余的油旁路流回油箱，在整个过程中，电机的转速是不变的，故供油量也是固定的，而由于执行动作是间隙性的，也并不可能是满负载的，因此定量供油就有很大的浪费空间。

I didn't watch TV last night, because it .

昨晚我没有看电视，因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来，在北京的很多小区里，电梯液晶电视被撤了下来。